1000 |
System error %1
|
1001 |
System error %1
|
1002 |
System error %1
|
1003 |
Alarm pointer for this self-clearing alarm %1 is zero
|
1004 |
Alarm reaction to NCK alarm incorrectly configured
|
1005 |
Operating system error %1 parameter %2 %3 %4
|
1010 |
Channel %1 system error %2 action %3
|
1011 |
Channel %1 %3 %4 system error %2
|
1012 |
Channel %1 system error %2 %3 %4
|
1013 |
Channel %1 system error %2
|
1014 |
Channel %1 system error %2
|
1015 |
Channel %1 axis %2 system error %3
|
1016 |
Channel %1 axis %2 system error %3
|
1017 |
Channel %1 axis %2 system error %3
|
1018 |
Floating point arithmetic error in channel %1 task %2 station %3 FPU state %4 %4
|
1019 |
Floating point arithmetic error at address %3 in channel %1 task %2 FPU state %4
|
1030 |
System error in link module error code %1 error type %2
|
1031 |
Link module generated an unspecified error %1 NCU %2 %3 %4
|
1100 |
No valid firmware
|
1160 |
Assertion failed in %1: %2
|
2000 |
PLC sign-of-life monitoring
|
2001 |
PLC has not started up
|
2100 |
NCK battery warning threshold reached
|
2101 |
NCK battery alarm
|
2102 |
NCK battery alarm
|
2110 |
NCK temperature alarm
|
2120 |
NCK fan alarm
|
2130 |
5V/24V encoder or 15V D/A converter under voltage
|
2140 |
The actual service switch position forces a SRAM to be cleared at the next Power On (general reset active)
|
2190 |
Hardware plug-in module for communication with the digitizer missing
|
2192 |
No NCU link module exists, MD %1 reset
|
2193 |
“Safety Integrated” is not available for link axis %1.
|
2195 |
Channel %1 axis %2 high-speed punching/nibbling not possible via link
|
2196 |
Link axis active and $MN_MM_SERVO_FIFO_SIZE != %1
|
2900 |
Reboot is delayed
|
3000 |
Emergency stop
|
3001 |
Internal emergency stop
|
4000 |
Channel %1 machine data %2[%3] has gap in axis assignment
|
4001 |
Channel %1 axis %2 defined for more than one channel via machine data %3
|
4002 |
Channel %1 machine data %2[%3] assigns an axis not defined in channel
|
4003 |
Axis %1 incorrect assignment of master channel in machine data %2
|
4004 |
Channel %1 machine data %2 axis %3 defined repeatedly as geometry axis
|
4005 |
Maximum number of axes in channel %1 exceeded. Limit %2
|
4007 |
Axis %1 incorrect assignment of master NCU in machine data %2
|
4010 |
Invalid identifier used in machine data %1[%2]
|
4011 |
Channel %1 invalid identifier used in machine data %2[%3]
|
4012 |
Invalid identifier used in machine data %1[%2]
|
4013 |
Invalid NCU link configuration by machine data %1 = %2 , on NCU_1 = %3
|
4014 |
Axis %1 defined several times in %2
|
4016 |
Axis %1 already used by NCU %2
|
4017 |
Axis container %1, location %2 already used by NCU %3
|
4018 |
Axis container %1, location %2 not used by any channel
|
4019 |
Axis container %1 advance not allowed with current status of NCU %2
|
4020 |
Identifier %1 used several times in machine data %2
|
4021 |
Channel %1 identifier %2 used several times in machine data %3
|
4022 |
Axis container %3 switch not allowed: ext. zero offset active channel %1 axis %2
|
4023 |
Axis container %1 switch not allowed, axis container %2 switch active
|
4024 |
Invalid axis configuration due to missing axis container machine data
|
4025 |
Axis container %3 switch not allowed: master/slave active channel %1 axis %2
|
4026 |
Machine data %1[%2], link axis NC%3_AX%4 not used by any channel
|
4027 |
Notice: MD %1 was also changed for the other axes of axis container %2
|
4028 |
Notice! The axial MDs of the axes of the axis containers were matched.
|
4029 |
Notice: the axial MDs in axis container %1 will be matched on the next power-up
|
4030 |
Channel %1 axis identifier missing in machine data %2[%3]
|
4031 |
Channel %1 link axis %2 defined for more than one channel in machine data %3
|
4032 |
Channel %1 wrong identifier for facing axis in %2
|
4033 |
Notice: NCU link communication still not connected
|
4034 |
Local link axis %1 is not allowed for different interpolation cycle time = %2/%3
|
4035 |
Interpolation cycle from NCU%1 = %2 does not match NCU%3 = %4
|
4036 |
Wrong NCU link configuration by MD %1
|
4040 |
Channel %1 axis identifier %2 not consistent with machine data %3
|
4045 |
Channel %1 conflict between machine data %2 and machine data %3
|
4050 |
NC code identifier %1 cannot be reconfigured to %2
|
4060 |
Standard machine data loaded
|
4062 |
Backup data loaded
|
4065 |
Buffered memory was restored from backup medium (potential loss of data!)
|
4066 |
Buffered memory of FFS restored from backup medium (potential loss of data!)
|
4070 |
Normalizing machine data has been altered
|
4073 |
Compile cycle functions define machine data number %1 several times
|
4075 |
Machine data %1 (and maybe others) not altered due to missing permission level %2
|
4076 |
%1 Machine data could not be altered with permission level %2
|
4077 |
New value %1 of MD %2 not set. Requested %3 bytes too much %4 memory.
|
4080 |
Incorrect configuration of indexing axis in MD %1
|
4090 |
Too many errors during power-up
|
4100 |
System cycle time/scan time divider corrected for digital drive
|
4102 |
Default values for drive cycle times differ
|
4110 |
IPO factor increased to %1
|
4111 |
PLC cycle increased to %1 ms
|
4112 |
Servo cycle changed to %1 ms
|
4113 |
Sysclock cycle changed to %1 ms
|
4114 |
Error in DP cycle of SDB1000
|
4115 |
Time ratio communication to Ipo changed to %1
|
4150 |
Channel %1 invalid M function sub program call configured
|
4152 |
Illegal configuration of the “Block display with absolute values” function
|
4160 |
Channel %1 invalid M function number configured for spindle switchover
|
4170 |
Invalid M function number for channel synchronisation assigned
|
4180 |
Invalid M function number assigned to enable ASUP
|
4181 |
Channel %1 invalid assignment of an M auxiliary function number
|
4182 |
Channel %1 invalid M auxiliary function number in %2%3, MD reset
|
4183 |
Channel %1 M auxiliary function number %2 used several times (%3 and %4)
|
4184 |
Channel %1 illegally predefined auxiliary function in %2%3, MD reset
|
4185 |
Channel %1 illegal auxiliary function configured %2 %3 %4
|
4200 |
Channel %1 geometry axis %2 must not be declared a rotary axis
|
4210 |
Channel %1 spindle %2 declaration as rotary axis missing
|
4215 |
Channel %1 spindle %2 declaration as modulo axis missing
|
4220 |
Channel %1 spindle %2 declared repeatedly
|
4225 |
Channel %1 axis %2 declaration as rotary axis missing
|
4230 |
Channel %1 data alteration from external not possible in current channel state
|
4240 |
Runtime overflow for IPO cycle or position controller cycle, IP %1
|
4250 |
FastPlcCom functionality not available
|
4252 |
PLCIO read error: %1
|
4254 |
PLCIO write error: %1
|
4260 |
Machine data %1 illegal
|
4270 |
Machine data %1 assigns not activated NCK input/output byte %2
|
4275 |
Machine data %1 and %2 both assign the same NCK output byte no. %3 several times
|
4280 |
Assignment of NCK input/output byte via MD %1[%2] does not match hardware configuration
|
4282 |
Hardware of external NCK outputs assigned repeatedly
|
4285 |
Error on terminal block %1, error code %2
|
4290 |
Local P-bus sign-of-life monitoring
|
4291 |
Module in local P-bus slot %1 error codes %2 %3 %4 %2 %3 %4
|
4300 |
Declaration in MD %1 is not allowed for geometry axis/spindle %2.
|
4310 |
Declaration in MD %1 index %2 is not allowed.
|
4320 |
Axis %1 function %2 %3 and %4 not allowed
|
4334 |
Channel %1 The amount of fine correction in parameter %2 of the orientable toolholder %3 is too large
|
4336 |
Channel %1 orientable toolholder no. %2 for orientation transformation %3 does not exist
|
4338 |
Channel %1 invalid transformation type ‘%2’ in toolholder %3 for orientation transformer %4
|
4340 |
Channel %1 block %2 invalid transformation type in transformation no. %3
|
4341 |
Channel %1 block %2 no data set available for transformation no. %3
|
4342 |
Channel %1 invalid machine data for general 5-axis transformation error no. %2
|
4343 |
Channel %1 attempt made to change the machine data of an active transformation.
|
4345 |
Channel %1 invalid configuration in chained transformation no.%2
|
4346 |
Channel %1 invalid geoaxis assignment in machine data %2[%3]
|
4347 |
Channel %1 invalid channel axis assignment in machine data %2[%3]
|
4350 |
Channel %1 axis identifier %2 machine data %3 not consistent with machine data %4
|
4400 |
MD alteration will cause reorganisation of buffered memory (loss of data!)
|
4502 |
Channel %1 anachronism %2(%3) -> %4
|
5000 |
Communication job not executable %1
|
6000 |
Memory reorganized using standard machine data
|
6010 |
Channel %1 data block %2 not or not completely created, error code %3
|
6020 |
Machine data have been altered – now memory is reorganized
|
6030 |
Limit of user memory has been adapted
|
6035 |
Instead of %1 KB the system has only %2 KB of free user memory of type “%3”
|
6100 |
Error while creating %1, error number %2 %3
|
6401 |
Channel %1 tool change not possible: Empty location for tool %2 Duplo no. %3 on magazine %4 not available.
|
6402 |
Channel %1 tool change not possible. Magazine no. %2 not available
|
6403 |
Channel %1 tool change not possible. Magazine location number %2 on magazine %3 not available.
|
6404 |
Channel %1 tool change not possible. Tool %2 not available or not usable
|
6405 |
Channel %1 command %2 has invalid PLC acknowledge parameter %3 – identifier %4
|
6406 |
Channel %1 PLC acknowledge for command %2 is missing
|
6407 |
Channel %1 tool %2 cannot be placed in magazine %3 on location %4.Invalid definition of magazine!
|
6410 |
TO unit %1 tool %2 / Duplo no. %3 has reached its pre warning limit with D = %4
|
6411 |
Channel %1 tool %2 / Duplo no. %3 has reached its prewarning limit with D = %4
|
6412 |
TO unit %1 tool %2 / Duplo no. %3 has reached its monitoring limit with D = %4
|
6413 |
Channel %1 tool %2 / Duplo no. %3 has reached its monitoring limit with D = %4
|
6421 |
Channel %1 tool move not possible. Empty location for tool %2 Duplo no. %3 on magazine %4 not available.
|
6422 |
Channel %1 tool move not possible. Magazine no. %2 not available.
|
6423 |
Channel %1 tool move not possible. Location %2 on magazine %3 not available.
|
6424 |
Channel %1 tool move not possible. Tool %2 not available/not usable.
|
6425 |
Channel %1 tool %2 cannot be placed in magazine %3 on location %4. Invalid definition of magazine!
|
6430 |
Workpiece counter: overflow in table of monitored cutting edges.
|
6431 |
Function not allowed. Tool management/monitoring is not active.
|
6432 |
Function not executable. No tool assigned to tool holder/spindle
|
6433 |
Channel %1 block %2 %3 not available with tool management
|
6434 |
Channel %1 block %2 NC command SETMTH not allowed because tool holder function not active
|
6441 |
Writing of $P_USEKT not allowed.
|
6442 |
Channel %1 function not executable. No tool assigned to desired magazine/magazine location %2.
|
6450 |
Channel %1 tool change not possible. Invalid magazine location no. %2 in buffer magazine
|
6451 |
Channel %1 tool change not possible. No buffer magazine defined.
|
6452 |
Channel %1 tool change not possible. Tool holder/spindle number = %2 not defined.
|
6453 |
Channel %1 tool change not possible. No assignment between toolholder/spindle no. = %2 and buffer magazine location %3
|
6454 |
Channel %1 tool change not possible. No distance relation available.
|
6500 |
NC memory full
|
6510 |
Too many part programs in the NC memory
|
6520 |
The value of the machine data %1%2 is too low
|
6530 |
Too many files in directory
|
6540 |
Too many directories in the NC memory
|
6550 |
Too many subdirectories
|
6560 |
Data format not allowed
|
6570 |
NC memory full
|
6580 |
NC memory full
|
6600 |
NC card memory is full
|
6610 |
Too many files open on NC card
|
6620 |
NC card has incorrect format
|
6630 |
NC card hardware is defective
|
6640 |
NC card is not inserted
|
6650 |
Write protection of NC card is active
|
6660 |
‘Flash File System’ option is not set
|
6670 |
NC card read active
|
6671 |
NC card write active
|
6690 |
Cycles from NC card cannot be copied to the passive file system.
|
6691 |
Cycles from the passive file system cannot be saved on the NC card
|
6692 |
Cycle %1 lost
|
6693 |
File %1 lost
|
6698 |
Unknown NC card (%1/%2). Writing not possible.
|
6700 |
Channel %1 value of the machine data %2%3 is too low
|
7000 |
Too many compile cycle alarms defined
|
7010 |
Range of MMC alarm numbers for compile cycles exceeded
|
7020 |
Compile cycle alarm number has not been defined
|
7100 |
Compile cycles VDI area: %1 byte for inputs and %2 byte for outputs. Maximum %3 bytes available.
|
7200 |
Problem with externally linked compile cycle %1 %2
|
7201 |
Assertion error in %1 line %2
|
7202 |
Missing option bit for %1: %2
|
8000 |
Channel %1 option ‘user interrupt programs’ not set
|
8010 |
Option ‘activation of more than %1 axes’ not set
|
8020 |
Option ‘activation of more than %1 channels’ not set
|
8021 |
Option ‘activation of more than %1 mode groups’ not set
|
8022 |
Option ‘activation of more than %1KB SRAM’ not set
|
8030 |
Channel %1 block %2 option ‘interpolation of more than 4 axes’ not set
|
8032 |
Option ‘activation of more than %1 link axes’ not set
|
8034 |
Option ‘activation of axis containers’ not set
|
8036 |
Option: it is not allowed to set different IPO cycles or position control cycles with NCU link.
|
8038 |
Option ‘activation of more than %1 lead link axes’ not set
|
8040 |
Machine data %1 reset, corresponding option is not set
|
8041 |
Axis %1: MD %2 reset, corresponding option not sufficient
|
8044 |
Option for IPO cycle time %1 ms not set
|
8045 |
Option for selected cycle settings not set
|
8080 |
%1 options are activated without setting the license key
|
8081 |
%1 options are activated that are not licensed by the license key
|
8082 |
The license key was entered three times, Power On required before next try.
|
8098 |
Invalid combination of options (%1)
|
8100 |
Channel %1 block %2: function not possible
|
10203 |
Channel %1 NC start without reference point
|
10207 |
Channel %1 error when selecting or deselecting the digitize function
|
10208 |
Channel %1 continue program with NC start
|
10209 |
Channel %1 internal NC stop after block search
|
10222 |
Channel %1 inter-channel communication not possible
|
10223 |
Channel %1: Command %2 is already occupied
|
10225 |
Channel %1: command denied
|
10299 |
Channel %1 Auto-Repos function is not enabled
|
10600 |
Channel %1 block %2 auxiliary function during thread cutting active
|
10601 |
Channel %1 block %2 zero velocity at block end point during thread cutting
|
10604 |
Channel %1 block %2 thread lead increase too high
|
10605 |
Channel %1 block %2 thread lead decrease too high
|
10607 |
Channel %1 block %2 thread with frame not executable
|
10610 |
Channel %1 axis %2 not stopped
|
10620 |
Channel %1 block %3 axis %2 at software limit switch %4
|
10621 |
Channel %1 axis %2 rests on software limit switch %3
|
10630 |
Channel %1 block %2 axis %3 at working area limit %4
|
10631 |
Channel %1 axis %2 rests at working area limit %3
|
10650 |
Channel %1 axis %2 incorrect gantry machine data, error code %3
|
10651 |
Channel %1 illegal gantry configuration. Error code %2
|
10652 |
Channel %1 axis %2 gantry warning threshold exceeded
|
10653 |
Channel %1 axis %2 gantry error threshold exceeded
|
10654 |
Channel %1 waiting for synchronization start of gantry group %2
|
10655 |
Channel %1 synchronization of gantry group %2 in progress
|
10656 |
Channel %1 axis %2 gantry alarm not yet used
|
10700 |
Channel %1 block %2 NCK protection zone %3 violated during automatic or MDA mode
|
10701 |
Channel %1 block %2 channel-specific protection zone %3 violated during automatic or MDA mode
|
10702 |
Channel %1 NCK protection zone %2 violated during manual mode
|
10703 |
Channel %1 channel-specific protection zone %2 violated during manual mode
|
10704 |
Channel %1 block %2 protection zone monitoring is not guaranteed
|
10706 |
Channel %1 NCK protection zone %2 reached with axis %3 during manual mode
|
10707 |
Channel %1 channel-specific protection zone %2 reached with axis %3 during manual mode
|
10710 |
Channel %1 block %2 conflict with centre less grinding
|
10720 |
Channel %1 block %3 axis %2 software limit switch %4
|
10721 |
Channel %1 block %3 axis %2 software limit switch %4
|
10730 |
Channel %1 block %3 axis %2 working area limitation %4
|
10731 |
Channel %1 block %3 axis %2 working area limitation %4
|
10740 |
Channel %1 block %2 too many empty blocks in WAB programming
|
10741 |
Channel %1 block %2 direction reversal with WAB infeed motion
|
10742 |
Channel %1 block %2 WAB distance invalid or not programmed
|
10743 |
Channel %1 block %2 WAB programmed several times
|
10744 |
Channel %1 block %2 no valid WAB direction defined
|
10745 |
Channel %1 block %2 WAB end position not clear
|
10746 |
Channel %1 block %2 block search stop for WAB
|
10747 |
Channel %1 block %2 retraction direction not defined for WAB
|
10748 |
Channel %1 block %2 illegal retract plane with WAB
|
10750 |
Channel %1 block %2 tool radius compensation activated without tool number
|
10751 |
Channel %1 block %2 danger of collision due to tool radius compensation
|
10752 |
Channel %1 block %2 overflow of local block buffer with tool radius compensation
|
10753 |
Channel %1 block %2 selection of the tool radius compensation only possible in linear block
|
10754 |
Channel %1 block %2 deselection of the tool radius compensation only possible in linear block
|
10755 |
Channel %1 block %2 selection of the tool radius compensation via KONT not possible at the current starting point
|
10756 |
Channel %1 block %2 deselection of the tool radius compensation via KONT not possible at the programmed end point
|
10757 |
Channel %1 block %2 changing the compensation plane while tool radius compensation is active not possible
|
10758 |
Channel %1 block %2 curvature radius with variable compensation value too small
|
10759 |
Channel %1 block %2 path is parallel to tool orientation
|
10760 |
Channel %1 block %2 helical axis is not parallel to tool orientation
|
10761 |
Channel %1 block %2 tool radius compensation for ellipse with more than one revolution not possible
|
10762 |
Channel %1 block %2 too many empty blocks between two traversing blocks with active tool radius compensation
|
10763 |
Channel %1 block %2 path component of the block in the compensation plane becomes zero
|
10764 |
Channel %1 block %2 discontinuous path with active tool radius compensation
|
10765 |
Channel %1 block %2 3D tool radius compensation not possible
|
10766 |
Channel %1 illegal change of surface orientation between block %2 and block %3
|
10767 |
Channel %1 block %2 processing with tilt angle unequal 0 not possible
|
10768 |
Channel %1 block %2 illegal tool orientation with 3D tool radius compensation
|
10769 |
Channel %1 block %2 Illegal surface normal vector with 3D tool radius compensation
|
10770 |
Channel %1 block %2 change of corner type due to change of orientation with active tool radius compensation
|
10771 |
Channel %1 block %2 overflow of local block buffer due to orientation smoothing
|
10772 |
Channel %1 block %2 illegal orientation change when activating or deactivating 3D face cutting
|
10773 |
Channel %1 illegal tool orientation in block %2 at inside corner with block %3
|
10774 |
Channel %1 illegal tool dimensions with face cutting in block %2
|
10775 |
Channel %1 illegal tool change with face cutting in block %2
|
10776 |
Channel %1 block%2 axis %3 must be geometry axis if tool radius compensation is active
|
10777 |
Channel %1 block %2 tool radius compensation: too many blocks with suppression of compensation
|
10778 |
Channel %1 block %2 preprocessing stop with active tool radius compensation
|
10779 |
Channel %1 block %2 preprocessing stop with active tool radius compensation
|
10780 |
Channel %1 block %2 preprocessing stop with active tool radius compensation
|
10781 |
Channel %1 block %2 illegal orientation of involute with tool radius compensation
|
10782 |
Channel %1 block %2 illegal curve type with tool radius compensation
|
10783 |
Channel %1 block %2 tool radius compensation type requires orientation transformation
|
10784 |
Channel %1 block %2 illegal tool for tool radius compensation with constraint surface
|
10790 |
Channel %1 block %2 plane change during linear programming with angles
|
10791 |
Channel %1 block %2 invalid angle during linear programming
|
10792 |
Channel %1 block %2 illegal interpolation type during linear programming with angles
|
10793 |
Channel %1 block %2 second block missing during linear programming with angles
|
10794 |
Channel %1 block %2 angle specification missing in second block during linear interpolation with angles
|
10795 |
Channel %1 block %2 end point specification during angle programming contradictory
|
10800 |
Channel %1 block %3 axis %2 is not a geometry axis
|
10805 |
Channel %1 block %2 repositioning after switch of geometry axes or transformation
|
10810 |
Channel %1 block %2 master spindle not defined
|
10820 |
Channel %1 rotary axis/spindle %2 not defined
|
10860 |
Channel %1 block %2 feedrate not programmed
|
10861 |
Channel %1 block %3 velocity of positioning axis %2 is zero
|
10862 |
Channel %1 block %2 master spindle also used as path axis
|
10870 |
Channel %1 block %2 facing axis not defined
|
10880 |
Channel %1 block %2 too many empty blocks between two traversing blocks when inserting chamfers or radii
|
10881 |
Channel %1 block %2 overflow of local block buffer when inserting chamfers or radii
|
10882 |
Channel %1 block %2 activation of chamfers or radii (non-modal) without traversing movement in the block
|
10883 |
Channel %1 block %2 chamfer or fillet has to be reduced
|
10890 |
Channel %1 block %2 overflow of local block buffer when calculating splines
|
10891 |
Channel %1 block %2 multiplicity of node is greater than its order
|
10900 |
Channel %1 block %2 no S value programmed for constant cutting speed
|
10910 |
Channel %1 block %2 excessive velocity of one path axis
|
10911 |
Channel %1 block %2 transformation prohibits to traverse the pole
|
10912 |
Channel %1 block %2 preprocessing and main run might not be synchronized
|
10913 |
Channel %1 block %2 negative feed profile is ignored
|
10914 |
Movement not possible while transformation active – in channel %1, block %2
|
10930 |
Channel %1 block %2 interpolation type not allowed in stock removal contour
|
10931 |
Channel %1 block %2 incorrect stock removal contour
|
10932 |
Channel %1 block %2 preparation of contour has been restarted
|
10933 |
Channel %1 block %2 contour program does not contain enough contour blocks
|
10934 |
Channel %1 block %2 array for contour segmentation is set too small
|
10940 |
Channel %1 block %2 curve table %3: delete/overwrite not possible
|
10941 |
Channel %1 block %2 curve table %3: NC memory full
|
10942 |
Channel %1 block %2 curve table %3: illegal instruction during definition
|
10943 |
Channel %1 block %2 curve table %3: direction reversal of lead value in the block not allowed
|
10944 |
Channel %1 block %2 curve table %3: illegal transformation
|
10945 |
Channel %1 block %2 curve table %3: illegal coupling of axes
|
10946 |
Channel %1 block %2 curve table %3: no contour defined
|
10947 |
Channel %1 block %2 curve table %3: contour not continuous
|
10948 |
Channel %1 block %2 curve table %3: position jump at end of period
|
10949 |
Channel %1 block %2 curve table %3: missing master axis motion
|
10950 |
Channel %1 calculation of arc length function too inaccurate
|
10951 |
Channel %1 block %2 curve table %3: following value period is zero
|
10955 |
Channel %1 block %2 curve table %3: missing master axis motion
|
10956 |
Channel %1 block %2 curve table %3: NC memory limit DRAM reached
|
10960 |
Channel %1 block %2 COMPCURV/COMPCAD and radius compensation cannot be used simultaneously
|
10961 |
Channel %1 block %2 maximum cubic polynomials are allowed on active radius compensation.
|
10962 |
Channel %1 block %2 function %3 not possible with path correction
|
12000 |
Channel %1 block %2 address %3 programmed repeatedly
|
12010 |
Channel %1 block %2 address %3 address type programmed too often
|
12020 |
Channel %1 block %2 illegal address modification
|
12030 |
Channel %1 block %2 invalid parameter or data type in %3
|
12040 |
Channel %1 block %2 expression %3 is not of data type ‘AXIS’
|
12050 |
Channel %1 block %2 DIN address %3 not configured
|
12060 |
Channel %1 block %2 same G group programmed repeatedly
|
12070 |
Channel %1 block %2 too many syntax-defining G functions
|
12080 |
Channel %1 block %2 syntax error in text %3
|
12090 |
Channel %1 block %2 unexpected parameter %3
|
12100 |
Channel %1 block %2 number of passes %3 not permissible
|
12110 |
Channel %1 block %2 block syntax cannot be interpreted
|
12120 |
Channel %1 block %2 G function not separately programmed
|
12130 |
Channel %1 block %2 illegal tool orientation
|
12140 |
Channel %1 block %2 functionality %3 not implemented
|
12150 |
Channel %1 block %2 operation %3 not compatible with data type
|
12160 |
Channel %1 block %2 range of values exceeded
|
12170 |
Channel %1 block %2 identifier %3 defined repeatedly
|
12180 |
Channel %1 block %2 illegal chaining of operators %3
|
12190 |
Channel %1 block %2 variable of type ARRAY has too many dimensions
|
12200 |
Channel %1 block %2 symbol %3 cannot be created
|
12210 |
Channel %1 block %2 string %3 too long
|
12220 |
Channel %1 block %2 binary constant %3 in string too long
|
12230 |
Channel %1 block %2 hexadecimal constant %3 in string too long
|
12240 |
Channel %1 block %2 tool orientation %3 defined repeatedly
|
12250 |
Channel %1 block %2 nested macro %3 not possible
|
12260 |
Channel %1 block %2 too many initialization values specified %3
|
12261 |
Channel %1 block %2 initialization of %3 not allowed
|
12270 |
Channel %1 block %2 macro identifier %3 already defined
|
12280 |
Channel %1 block %2 maximum macro length %3 exceeded
|
12290 |
Channel %1 block %2 arithmetic variable % 3 not defined
|
12300 |
Channel %1 block %2 call-by-reference parameter missing on subroutine call %3
|
12310 |
Channel %1 block %2 axis parameter missing on procedure call %3
|
12320 |
Channel %1 block %2 parameter %3 is no variable
|
12330 |
Channel %1 block %2 type of parameter %3 incorrect
|
12340 |
Channel %1 block %2 number of parameters too high %3
|
12350 |
Channel %1 block %2 parameter %3 no longer possible
|
12360 |
Channel %1 block %2 dimension of parameter %3 incorrect
|
12370 |
Channel %1 block %2 range of values %3 not permissible
|
12380 |
Channel %1 block %2 maximum memory capacity reached
|
12390 |
Channel %1 block %2 initialization value %3 cannot be converted
|
12400 |
Channel %1 block %2 field %3 element does not exist
|
12410 |
Channel %1 block %2 incorrect index type for %3
|
12420 |
Channel %1 block %2 identifier %3 too long
|
12430 |
Channel %1 block %2 specified index is invalid
|
12440 |
Channel %1 block %2 maximum number of formal arguments exceeded
|
12450 |
Channel %1 block %2 label defined twice
|
12460 |
Channel %1 block %2 maximum number of symbols exceeded with %3
|
12470 |
Channel %1 block %2 G function %3 is unknown
|
12475 |
Channel %1 block %2 invalid G function number %3 programmed
|
12480 |
Channel %1 block %2 subroutine %3 already defined
|
12490 |
Channel %1 block %2 access permission level %3 is not valid
|
12500 |
Channel %1 block %2 in this module %3 is not possible
|
12510 |
Channel %1 block %2 too many machine data %3
|
12520 |
Channel %1 block %2 too many tool parameters %3
|
12530 |
Channel %1 block %2 invalid index for %3
|
12540 |
Channel %1 block %2 Block is too long or too complex
|
12550 |
Channel %1 block %2 name %3 not defined or option not installed
|
12552 |
Channel %1 block %2 tool/magazine OEM parameter not defined. Option not set.Option not set.
|
12560 |
Channel %1 block %2 programmed value %3 exceeds allowed limits
|
12570 |
Channel %1 block %2 too many motion synchronous actions in %3
|
12571 |
Channel %1 block %2 %3 not permissible for motion synchronous action
|
12572 |
Channel %1 block %2 %3 only permissible for motion synchronous action
|
12580 |
Channel %1 block %2 %3 not permissible for assignment in motion synchronous action
|
12581 |
Channel %1 block %2 invalid read access to %3 while in motion synchronous action
|
12582 |
Channel %1 block %2 field index %3 incorrect
|
12583 |
Channel %1 block %2 variable %3 no system variable
|
12584 |
Channel %1 block %2 variable %3 cannot be read synchronously with motion
|
12585 |
Channel %1 block %2 variable %3 cannot be changed synchronously with motion
|
12586 |
Channel %1 block %2 motion synchronous action: type conflict in variable %3
|
12587 |
Channel %1 block %2 motion synchronous action: operation/function %3 not allowed
|
12588 |
Channel %1 block %2 motion synchronous action: address %3 not allowed
|
12589 |
Channel %1 block %2 motion synchronous action: variable %3 not allowed with modal ID
|
12590 |
Channel %1 block %2 global user data cannot be created
|
12600 |
Channel %1 block %2 invalid line checksum
|
12610 |
Channel %1 block %2 accessing single character with call-by-reference parameter not possible %3
|
12620 |
Channel %1 block %2 accessing this variable as single character not possible
|
12630 |
Channel %1 block %2 skip ID/label in control structure not allowed
|
12640 |
Channel %1 block %2 invalid nesting of control structures
|
12641 |
Channel %1 block %2 maximum nesting depth of control structures exceeded
|
12650 |
Channel %1 block %2 axis identifier %3 different in channel %4
|
12660 |
Channel %1 block %2 motion synchronous action: variable %3 reserved for motion synchronous actions and technology cycles
|
12661 |
Channel %1 block %2 technology cycle %3: no further subprogram call possible
|
12700 |
Channel %1 block %2 contour definition programming not allowed as modal sub program is active
|
12701 |
Channel %1 block %2 illegal interpolation type for contour definition active
|
12710 |
Channel %1 block %2 illegal language element in external language mode
|
12720 |
Channel %1 block %2 program number for macro call (G65/G66) missing
|
12722 |
Channel %1 block %2 multiple ISO_2/3 macro or cycle calls in the block
|
12724 |
Channel %1 block %2 no radius programmed for cylinder interpolation activation/deactivation
|
12726 |
Channel %1 block %2 illegal plane selection with parallel axes
|
12728 |
Channel %1 block %2 distance for double turret not set
|
12730 |
Channel %1 block %2 no valid transformation machine data parametrized
|
12740 |
Channel %1 block %2 modal macro call %3 not possible
|
14000 |
Channel %1 block %2 illegal end of file
|
14001 |
Channel %1 block %2 illegal end of block
|
14009 |
Channel %1 block %2 illegal program path %3
|
14010 |
Channel %1 block %2 invalid default parameter in subroutine call
|
14011 |
Channel %1 block %2 program %3 not existing or will be edited
|
14012 |
Channel %1 block %2 maximum subroutine level exceeded
|
14013 |
Channel %1 block %2 number of subroutine passes invalid
|
14014 |
Channel %1 selected program %3 not available or will be edited
|
14015 |
Channel %1 block %2 program %3 is not enabled
|
14016 |
Channel %1 block %2 error when calling the subroutine via M/T function
|
14017 |
Channel %1 block %2 syntax error when calling the subroutine via M function
|
14020 |
Channel %1 block %2 wrong value or wrong number of parameters on function or procedure call
|
14021 |
Channel %1 block %2 wrong value or wrong number of parameters on function or procedure call
|
14025 |
Channel %1 block %2 motion synchronous action: illegal modal ID
|
14026 |
Channel %1 block %2 motion synchronous action: invalid polynomial number in the FCTDEF command
|
14030 |
Channel %1 block %2 combine OSCILL and POSP during oscillation with in feed motion
|
14033 |
Channel %1 block %2 involute: no end point programmed
|
14034 |
Channel %1 block %2 involute: angle of rotation too large
|
14035 |
Channel %1 block %2 involute: start point invalid
|
14036 |
Channel %1 block %2 involute: end point invalid
|
14037 |
Channel %1 block %2 involute: radius invalid
|
14038 |
Channel %1 block %2 involute not definable: end point error
|
14039 |
Channel %1 block %2 involute: end point programmed several times
|
14040 |
Channel %1 block %2 error in end point of circle
|
14045 |
Channel %1 block %2 error in tangential circle programming
|
14048 |
Channel %1 block %2 wrong number of revolutions in circle programming
|
14050 |
Channel %1 block %2 nesting depth for arithmetic operations exceeded
|
14051 |
Channel %1 block %2 arithmetic error in part program
|
14060 |
Channel %1 block %2 invalid skip level with differential block skip
|
14070 |
Channel %1 block %2 memory for variables not sufficient for subroutine call
|
14080 |
Channel %1 block %2 jump destination %3 not found
|
14082 |
Channel %1 block %2 label %3 program section not found
|
14085 |
Channel %1 block %2 instruction not allowed
|
14088 |
Channel %1 block %2 axis %3 doubtful position
|
14090 |
Channel %1 block %2 illegal D number
|
14091 |
Channel %1 block %2 illegal function, index %3 %3
|
14092 |
Channel %1 block %2 axis %3 is wrong axis type
|
14093 |
Channel %1 block %2 path interval <= 0 with polynominal interpolation
|
14094 |
Channel %1 block %2 polynominal degree greater than 3 programmed for polynominal interpolation
|
14095 |
Channel %1 block %2 radius for circle programming too small
|
14096 |
Channel %1 block %2 illegal type conversion
|
14097 |
Channel %1 block %2 string cannot be converted to AXIS type
|
14098 |
Channel %1 block %2 conversion error: no valid number found
|
14099 |
Channel %1 block %2 result in string concatenation too long
|
14100 |
Channel %1 block %2 orientation transformation not available
|
14101 |
Channel %1 block %2 orientation transformation not active
|
14102 |
Channel %1 block %2 polynominal degree greater than 5 programmed for orientation vector angle
|
14110 |
Channel %1 block %2 Euler angles and orientation vector components programmed
|
14111 |
Channel %1 block %2 Euler angles, orientation vector and transformation axes programmed
|
14112 |
Channel %1 block %2 programmed orientation path not possible
|
14113 |
Channel %1 block %2 programmed lead angle too large
|
14114 |
Channel %1 block %2 programmed tilt angle too large
|
14115 |
Channel %1 block %2 illegal definition of workpiece surface
|
14116 |
Channel %1 block %2 absolute orientation programmed while ORIPATH is active
|
14117 |
Channel %1 block %2 no angle or direction of the cone programmed
|
14118 |
Channel %1 block %2 no end orientation programmed
|
14119 |
Channel %1 block %2 no intermediate orientation programmed
|
14120 |
Channel %1 block %2 plane determination for programmed orientation not possible
|
14122 |
Channel %1 block %2 angle and direction of the cone programmed
|
14123 |
Channel %1 block %2 nutation angle of the cone too small
|
14124 |
Channel %1 block %2 start tangent for orientation is zero
|
14125 |
Channel %1 block %2 programmed rotation is not possible
|
14129 |
Channel %1 block %2 orientation angles and orientation vector components programmed
|
14130 |
Channel %1 block %2 too many initialization values given
|
14131 |
Channel %1 block %2 orientation axes and lead/tilt angles programmed
|
14132 |
Channel %1 block %2 orientation axes incorrectly configured
|
14133 |
Channel %1 block %2 G code for orientation definition not allowed
|
14134 |
Channel %1 block %2 G code for orientation interpolation not allowed
|
14140 |
Channel %1 block %2 position programming without transformation not allowed
|
14144 |
Channel %1 block %2 PTP movement not allowed
|
14146 |
Channel %1 block %2 CP or PTP movement without transformation not allowed
|
14148 |
Channel %1 illegal reference system for Cartesian manual traverse
|
14150 |
Channel %1 block %2 illegal tool carrier number programmed or declared (MD)
|
14151 |
Channel %1 block %2 illegal tool carrier rotation
|
14152 |
Channel %1 block %2 tool carrier: invalid orientation. Error code: %3
|
14153 |
Channel %1 block %2 unknown tool carrier type: %3
|
14154 |
Channel %1 block %2 The amount of fine correction in parameter %3 of the orientable tool holder %4 is too large
|
14155 |
Channel %1 block %2 invalid base frame definition for tool carrier offset
|
14156 |
Channel %1 toolholder selection error at reset
|
14157 |
Channel %1 block %2 illegal interpolation type with MOVT
|
14159 |
Channel %1 block %2 more than two angles programmed with ROTS or AROTS
|
14160 |
Channel %1 block %2 tool length selection without geometry axis specification
|
14165 |
Channel %1 block %2 active T number does not match selected tool
|
14170 |
Channel %1 block %2 illegal interpolation type with tool length compensation
|
14180 |
Channel %1 block %2 H number is not defined
|
14185 |
Channel %1 block %2 D number is not defined
|
14190 |
Channel %1 block %2 H number with G49
|
14195 |
Channel %1 block %2 D number with G49
|
14197 |
Channel %1 block %2 D number and H number programmed simultaneously
|
14198 |
Channel %1 block %2 illegal change of tool direction with tool offset
|
14199 |
Channel %1 block %2 illegal plane change for tool with diameter component
|
14200 |
Channel %1 block %2 negative polar radius
|
14210 |
Channel %1 block %2 polar angle too large
|
14250 |
Channel %1 block %2 negative pole radius
|
14260 |
Channel %1 block %2 pole angle too large
|
14270 |
Channel %1 block %2 pole programmed incorrectly
|
14280 |
Channel %1 block %2 polar coordinates programmed incorrectly
|
14290 |
Channel %1 block %2 poly nominal degree greater than 5 programmed for poly nominal interpolation
|
14300 |
Channel %1 block %2 overlaid handwheel motion activated incorrectly
|
14310 |
Handwheel %1 configuration incorrect or inactive
|
14400 |
Channel %1 block %2 tool radius compensation active at transformation switchover
|
14401 |
Channel %1 block %2 transformation not available
|
14402 |
Channel %1 block %2 spline active at transformation change
|
14403 |
Channel %1 block %2 preprocessing and main run might not be synchronized
|
14404 |
Channel %1 block %2 illegal parametrization of transformation
|
14410 |
Channel %1 block %2 spline active at geometry axis changeover
|
14411 |
Channel %1 block %2 tool radius compensation active at geometry axis changeover
|
14412 |
Channel %1 block %2 transformation active at geometry axis changeover
|
14413 |
Channel %1 block %2 fine tool correction: changeover geometry/channel axis not allowed
|
14414 |
Channel %1 block %2 GEOAX function: incorrect call
|
14415 |
Channel %1 block %2 tangent control: changeover geometry/channel axis not allowed
|
14420 |
Channel %1 block %2 index axis %3 frame not allowed
|
14500 |
Channel %1 block %2 illegal DEF or PROC instruction in the part program
|
14510 |
Channel %1 block %2 PROC instruction missing on subroutine call
|
14520 |
Channel %1 block %2 illegal PROC instruction in data definition section
|
14530 |
Channel %1 block %2 EXTERN and PROC instruction do not correspond
|
14600 |
Channel %1 block %2 reload buffer %3 cannot be established
|
14601 |
Channel %1 block %2 reload buffer could not be deleted
|
14602 |
Channel %1 block %2 timeout during EXTCALL
|
14610 |
Channel %1 block %2 compensation block not possible
|
14650 |
Channel %1 block %2 SETINT instruction with invalid ASUP input
|
14660 |
Channel %1 block %2 SETINT instruction with invalid priority
|
14700 |
Channel %1 block %2 timeout during command to interpreter
|
14701 |
Channel %1 block %2 number of available NC blocks reduced by %3
|
14710 |
Channel %1 block %2 error in initialization sequence in function %3
|
14720 |
Channel %1 block %2 axes for centerless transformation not available
|
14730 |
Channel %1 block %2 conflict at activation of centerless transformation
|
14740 |
Channel %1 block %2 no tool data available for centerless grinding
|
14745 |
Channel %1 block %2 centerless grinding not active
|
14750 |
Channel %1 block %2 too many auxiliary functions programmed
|
14751 |
Channel %1 block %2 resources for motion synchronous actions not sufficient (code: %3)
|
14752 |
Channel %1 block %2 DELDTG | STOPREOF conflict
|
14753 |
Channel %1 block %2 motion synchronous actions with illegal interpolation type
|
14754 |
Channel %1 block %2 motion synchronous actions and wrong feed type
|
14755 |
Channel %1 block %2 motion synchronous actions without traverse motion
|
14756 |
Channel %1 block %2 motion synchronous action and wrong value
|
14757 |
Channel %1 block %2 motion synchronous action and wrong type
|
14758 |
Channel %1 block %2 programmed value not available
|
14759 |
Channel %1 block %2 motion synchronous action and wrong axis type
|
14760 |
Channel %1 block %2 auxiliary function of a group programmed repeatedly
|
14761 |
Channel %1 block %2 motion synchronous action: DELDTG function not allowed with active tool radius compensation
|
14762 |
Channel %1 block %2 too many PLC variables programmed
|
14763 |
Channel %1 block %2 too many link variables programmed
|
14764 |
NCU link cannot transfer all link variables immediately
|
14765 |
NCU link cannot transfer all link variables
|
14766 |
NCU link is heavily loaded, impending memory shortage
|
14767 |
Machine data matching via NCU link not complete
|
14770 |
Channel %1 block %2 auxiliary function programmed incorrectly
|
14780 |
Channel %1 block %2 unreleased option used
|
14790 |
Channel %1 block %2 axis %3 programmed by PLC
|
14800 |
Channel %1 block %2 programmed path speed less or equal to zero
|
14810 |
Channel %1 block %2 negative axis speed programmed for positioning axis %3
|
14811 |
Channel %1 block %2 incorrect value range for acceleration of axis/spindle %3
|
14812 |
Channel %1 block %2 SOFTA not available for axis %3
|
14815 |
Channel %1 block %2 negative thread lead change programmed
|
14820 |
Channel %1 block %2 negative value for maximum spindle speed programmed with constant cutting speed
|
14821 |
Channel %1 block %2 error in selection or deselection of GWPS
|
14822 |
Channel %1 block %2 incorrect programming of GWPS
|
14823 |
Channel %1 block %2 error on selection or deselection of tool monitoring
|
14824 |
Channel %1 block %2 conflict with GWPS
|
14840 |
Channel %1 block %2 incorrect value range for constant cutting speed
|
14900 |
Channel %1 block %2 center point and end point programmed simultaneously
|
14910 |
Channel %1 block %2 invalid angle of aperture for programmed circle
|
14920 |
Channel %1 block %2 intermediate point of circle incorrect
|
15000 |
Channel %1 block %2 channel-sync instruction using illegal mark
|
15010 |
Channel %1 block %2 program coordination instruction with invalid channel number
|
15020 |
Channel %1 block %2 CHANDATA instruction cannot be executed. Channel %3 is not active
|
15021 |
Channel %1 block %2 CHANDATA instruction with invalid channel number
|
15025 |
CHANDATA(%2): channel is not active. Channel data will be ignored.
|
15030 |
Channel %1 block %2 different measurement system settings
|
15100 |
Channel %1 block %2 REORG abort caused by log file overflow
|
15110 |
Channel %1 block %2 REORG not possible
|
15150 |
Channel %1 block %2 reload from external aborted
|
15160 |
Channel %1 block %2 wrong preprocessing configuration
|
15165 |
Channel %1 block %2 error when translating or interpreting PLC Asup %3
|
15166 |
Channel %1 user system asup _N_ASUP_SPF not available
|
15170 |
Channel %1 block %2 program %3 could not be compiled
|
15171 |
Channel %1 block %2 compiled program %3 older than the relevant subroutine
|
15175 |
Channel %1 block %2 program %3. Interfaces could not be built
|
15180 |
Channel %1 block %2 program %3 cannot be executed as INI file
|
15185 |
Channel %1 %2 errors in INI file
|
15190 |
Channel %1 block %2 not enough free memory for subroutine call
|
15300 |
Channel %1 block %2 invalid number-of-passed-blocks during block search
|
15310 |
Channel %1 block %2 file requested during block search is not available
|
15320 |
Channel %1 block %2 invalid block search command
|
15330 |
Channel %1 block %2 invalid block number as search target
|
15340 |
Channel %1 block %2 invalid label as search target
|
15350 |
Channel %1 block %2 search target not found
|
15360 |
Channel %1 illegal target of block search (syntax error)
|
15370 |
Channel %1 target of block search not found
|
15380 |
Channel %1 block %2 illegal incremental programming in axis %3
|
15390 |
Channel %1 block %2 %3 not executed during block search
|
15395 |
Channel %1 master-slave not executable during block search
|
15400 |
Channel %1 block %2 selected initial init file does not exist
|
15410 |
Channel %1 block %2 initialization file contains invalid M function
|
15420 |
Channel %1 block %2 instruction in current mode not allowed
|
15450 |
Channel %1 block %2 compiled program cannot be stored
|
15460 |
Channel %1 block %2 syntax error with modal function
|
15500 |
Channel %1 block %2 illegal angle of shear
|
15700 |
Channel %1 block %2 illegal cycle alarm number %3
|
15800 |
Channel %1 block %2 wrong starting conditions for CONTPRON/CONTDCON
|
15810 |
Channel %1 block %2 wrong array dimension for CONTPRON/CONTDCON
|
15900 |
Channel %1 block %2 touch probe not allowed
|
15910 |
Channel %1 block %2 touch probe not allowed
|
15950 |
Channel %1 block %2 no traverse motion programmed
|
15960 |
Channel %1 block %2 no traverse motion programmed
|
16000 |
Channel %1 block %2 invalid value for lifting direction
|
16005 |
Channel %1 block %2 invalid value for lifting distance
|
16010 |
Channel %1 block %2 machining stop after lift fast
|
16015 |
Channel %1 block %2 wrong axis identifier %3
|
16016 |
Channel %1 block %2 no retraction position programmed for axis %3
|
16020 |
Channel %1 repositioning in block %2 is not possible
|
16100 |
Channel %1 block %2 spindle %3 not available in the channel
|
16105 |
Channel %1 block %2 spindle %3 cannot be assigned
|
16110 |
Channel %1 block %2 spindle %3 for dwell time not in control mode
|
16120 |
Channel %1 block %2 invalid index for tool fine compensation
|
16130 |
Channel %1 block %2 instruction not allowed with FTOCON
|
16140 |
Channel %1 block %2 FTOCON not allowed
|
16150 |
Channel %1 block %2 invalid spindle number with PUTFTOCF
|
16200 |
Channel %1 block %2 spline and polynominal interpolation not available
|
16300 |
Channel %1 block %2 denominator polynominal with zero places within parameter range not allowed
|
16400 |
Channel %1 block %2 positioning axis %3 cannot participate in spline
|
16410 |
Channel %1 block %2 axis %3 is not a geometry axis
|
16420 |
Channel %1 block %2 axis %3 programmed repeatedly
|
16421 |
Channel %1 block %2 angle %3 programmed repeatedly in the block
|
16422 |
Channel %1 block %2 angle %3 programmed repeatedly in the block
|
16423 |
Channel %1 block %2 angle %3 programmed repeatedly in the block
|
16424 |
Channel %1 block %2 coordinate %3 programmed repeatedly in the block
|
16430 |
Channel %1 block %2 geometry axis %3 cannot traverse as positioning axis in rotated coordinate system
|
16440 |
Channel %1 block %2 rotation programmed for non-existent geometry axis
|
16500 |
Channel %1 block %2 chamfer or rounding negative
|
16510 |
Channel %1 block %2 no facing axis available
|
16700 |
Channel %1 block %2 axis %3 invalid feed type
|
16710 |
Channel %1 block %2 axis %3 master spindle not programmed
|
16715 |
Channel %1 block %2 axis %3 spindle not in standstill
|
16720 |
Channel %1 block %2 axis %3 thread lead is zero
|
16730 |
Channel %1 block %2 axis %3 wrong parameter
|
16740 |
Channel %1 block %2 no geometry axis programmed
|
16750 |
Channel %1 block %2 axis %3 SPCON not programmed
|
16751 |
Channel %1 block %2 spindle/axis %3 SPCOF not executable
|
16755 |
Channel %1 block %2 no stop required
|
16760 |
Channel %1 block %2 axis %3 S value missing
|
16761 |
Channel %1 block %2 axis/spindle %3 not programmable in the channel
|
16762 |
Channel %1 block %2 spindle %3 thread function is active
|
16763 |
Channel %1 block %2 axis %3 programmed speed is illegal (zero or negative)
|
16770 |
Channel %1 block %2 axis %3 no measuring system available
|
16771 |
Channel %1 following axis %2 overlaid movement not enabled
|
16776 |
Channel %1 block %2 curve table %3 does not exist for axis %4
|
16777 |
Channel %1 block %2 coupling: following axis %3 for lead axis %4 not available
|
16778 |
Channel %1 block %2 coupling: Ring coupling at following axis %3 and leading axis %4 impermissible
|
16779 |
Channel %1 block %2 coupling: too many couplings for axis %3, see active leading axis %4
|
16780 |
Channel %1 block %2 following spindle/axis missing
|
16781 |
Channel %1 block %2 master spindle/axis missing
|
16782 |
Channel %1 block %2 following spindle/axis %3 not available
|
16783 |
Channel %1 block %2 master spindle/axis %3 not available
|
16785 |
Channel %1 block %2 identical spindles/axes %3
|
16787 |
Channel %1 block %2 coupling parameter not changeable
|
16788 |
Channel %1 block %2 cyclic coupling
|
16789 |
Channel %1 block %2 multiple link
|
16790 |
Channel %1 block %2 Parameter is zero or missing
|
16791 |
Channel %1 block %2 parameter is not relevant
|
16792 |
Channel %1 block %2 too many couplings for axis/spindle %3
|
16793 |
Channel %1 block %2 coupling of axis %3 prohibits transformation change
|
16794 |
Channel %1 block %2 coupling of axis/spindle %3 prohibits reference point approach
|
16795 |
Channel %1 block %2 string cannot be interpreted
|
16796 |
Channel %1 block %2 coupling not defined
|
16797 |
Channel %1 block %2 coupling is active
|
16798 |
Channel %1 block %2 axis %3 is following axis and prohibits axis container rotation
|
16799 |
Channel %1 block %2 axis %3 is master axis and prohibits axis container rotation
|
16800 |
Channel %1 block %2 traverse instruction DC/CDC for axis %3 not allowed
|
16810 |
Channel %1 block %2 traverse instruction ACP for axis %3 not allowed
|
16820 |
Channel %1 block %2 traverse instruction ACN for axis %3 not allowed
|
16830 |
Channel %1 block %2 incorrect position programmed for axis/spindle %3
|
16903 |
Channel %1 program control: action %2 not allowed in the current state
|
16904 |
Channel %1 program control: action %2 not allowed in the current state
|
16905 |
Channel %1 program control: action %2 not allowed
|
16906 |
Channel %1 program control: action %2 is aborted due to an alarm
|
16907 |
Channel %1 action %2 only possible in stop state
|
16908 |
Channel %1 action %2 only possible in reset state or at the block end
|
16909 |
Channel %1 action %2 not allowed in current mode
|
16911 |
Channel %1 mode change is not allowed
|
16912 |
Channel %1 program control: action %2 only possible in reset state
|
16913 |
Mode group %1 channel %2 mode change: action %3 not allowed
|
16914 |
Mode group %1 channel %2 mode change: action %3 not allowed
|
16915 |
Channel %1 action %2 not allowed in the current block
|
16916 |
Channel %1 repositioning: action %2 not allowed in the current state
|
16918 |
Channel %1 for action %2 all channels must be in reset state
|
16919 |
Channel %1 action %2 is not allowed due to a pending alarm
|
16920 |
Channel %1 action %2 is already active
|
16921 |
Channel %1 mode group %2 machine data: channel/mode group assignment not allowed or assigned twice
|
16922 |
Channel %1 subprograms: action %2 maximum nesting depth exceeded
|
16923 |
Channel %1 program control: action %2 not allowed in the current state
|
16924 |
Channel %1 caution: program test modifies tool management data
|
16925 |
Channel %1 program control: action %2 not allowed in the current state, action %3 active
|
16926 |
Channel %1 channel coordination: action %2 not allowed in block %3, marker %4 is already set
|
16927 |
Channel %1 action %2 at active interrupt treatment not allowed
|
16928 |
Channel %1 interrupt treatment: action %2 not possible
|
16930 |
Channel %1: preceding block and current block %2 must be separated through an executable block
|
16931 |
Channel %1 subprograms: action %2 maximum nesting depth exceeded
|
16932 |
Channel %1 conflict when activating user data type %2
|
16933 |
Channel %1 interrupt treatment: action %2 not allowed in the current state
|
16934 |
Channel %1 interrupt treatment: action %2 not possible due to stop
|
16935 |
Channel %1 action %2 not possible due to search run
|
16936 |
Channel %1 action %2 not possible due to active dry run
|
16937 |
Channel %1 action %2 not possible due to program test
|
16938 |
Channel %1 action %2 aborted due to active gear change
|
16939 |
Channel %1 action %2 rejected due to active gear change
|
16940 |
Channel %1 action %2 wait for gear change
|
16941 |
Channel %1 action %2 rejected because no program event has been executed yet
|
16942 |
Channel %1 start program command action %2 not possible
|
16943 |
Channel %1 action %2 not possible due to ASUP
|
16944 |
Channel %1 action %2 not possible due to active search blocks
|
16945 |
Channel %1 action %2 delayed up to the block end
|
16946 |
Channel %1 start via START is not allowed
|
16947 |
Channel %1 start via PLC is not allowed
|
16948 |
Channel %1 dependent channel %2 still active
|
16949 |
Correspondence between marker of channel %1 and channel %2 is invalid.
|
16950 |
Channel %1 search run with hold block
|
16951 |
Channel %1 search run in a program section that cannot be searched
|
17000 |
Channel %1 block %2 maximum number of symbols exceeded
|
17001 |
Channel %1 block %2 no memory left for tool/magazine data
|
17010 |
Channel %1 block %2 no memory left
|
17020 |
Channel %1 block %2 illegal array index 1
|
17030 |
Channel %1 block %2 illegal array index 2
|
17040 |
Channel %1 block %2 illegal axis index
|
17050 |
Channel %1 block %2 illegal value
|
17055 |
Channel %1 block %2 GUD variable not existing
|
17060 |
Channel %1 block %2 requested data area too large
|
17070 |
Channel %1 block %2 data is write-protected
|
17080 |
Channel %1 block %2 %3 value below lower limit
|
17090 |
Channel %1 block %2 %3 value exceeds upper limit
|
17095 |
Channel %1 block %2 invalid value
|
17100 |
Channel %1 block %2 digital input/comparator no. %3 not activated
|
17110 |
Channel %1 block %2 digital output no. %3 not activated
|
17120 |
Channel %1 block %2 analog input no. %3 not activated
|
17130 |
Channel %1 block %2 analog output no. %3 not activated
|
17140 |
Channel %1 block %2 NCK output %3 is assigned to a function via machine data
|
17150 |
Channel %1 block %2 maximum of %3 NCK outputs programmable in the block
|
17160 |
Channel %1 block %2 no tool selected
|
17170 |
Channel %1 block %2 number of symbols too large
|
17180 |
Channel %1 block %2 illegal D number
|
17181 |
Channel %1 block %2 T no.= %3, D no.= %4 not existing
|
17182 |
Channel %1 block %2 illegal sum correction number
|
17188 |
Channel %1 D number %2 defined in tool T no. %3 and %4
|
17189 |
Channel %1 D number %2 of tools defined on magazine/location %3 and %4
|
17190 |
Channel %1 block %2 illegal T number
|
17191 |
Channel %1 block %2 T= %3 not existing, program %4
|
17192 |
TO unit %1 invalid tool designation of ‘%2’, duplo no. %3. No more replacement tools possible in ‘%4’.
|
17193 |
Channel %1 block %2 the active tool is no longer on toolholder no./spindle no. %3, program %4
|
17194 |
Channel %1 block %2 no suitable tool found
|
17200 |
Channel %1 block %2 deleting tool data not possible
|
17202 |
Channel %1 block %2 deleting magazine data not possible
|
17210 |
Channel %1 block %2 access to variable not possible
|
17212 |
Channel %1 tool management: Load manual tool %3, duplo no. %2 onto spindle/ toolholder %4
|
17214 |
Channel %1 tool management: remove manual tool %3 from spindle/toolholder %2
|
17216 |
Channel %1 tool management: remove manual tool from spindle/toolholder %4 and load manual tool %3, duplo no. %2
|
17220 |
Channel %1 block %2 tool not existing
|
17230 |
Channel %1 block %2 Duplo no. already assigned
|
17240 |
Channel %1 block %2 illegal tool definition
|
17250 |
Channel %1 block %2 illegal magazine definition
|
17260 |
Channel %1 block %2 illegal magazine location definition
|
17262 |
Channel %1 block %2 illegal tool adapter operation
|
17270 |
Channel %1 block %2 call-by-reference: illegal variable
|
17500 |
Channel %1 block %2 axis %3 is not an indexing axis
|
17501 |
Channel %1 block %2 indexing axis %3 with Hirth tool system is active
|
17502 |
Channel %1 block %2 indexing axis %3 with Hirth tooth system stop is delayed
|
17503 |
Channel %1 block %2 indexing axis %3 with Hirth tooth system and axis not referenced
|
17510 |
Channel %1 block %2 invalid index for indexing axis %3
|
17600 |
Channel %1 block %2 preset on transformed axis %3 not possible
|
17605 |
Channel %1 block %2 axis %3 transformation active: inhibits rotation of axis container
|
17610 |
Channel %1 block %2 axis %3 involved in the transformation, action cannot be carried out
|
17620 |
Channel %1 block %2 approaching fixed point for transformed axis %3 not possible
|
17630 |
Channel %1 block %2 referencing for transformed axis %3 not possible
|
17640 |
Channel %1 block %2 spindle operation for transformed axis %3 not possible
|
17650 |
Channel %1 block %2 machine axis %3 not programmable
|
17800 |
Channel %1 block %2 illegally coded position programmed
|
17900 |
Channel %1 block %2 axis %3 is no machine axis
|
18000 |
Channel %1 block %2 NCK-specific protection zone %3 wrong. Error code %4
|
18001 |
Channel %1 block %2 channel-specific protection zone %3 incorrect. Error code %4
|
18002 |
Channel %1 block %2 NCK protection zone %3 cannot be activated. Error code %4
|
18003 |
Channel %1 block %2 NCK protection zone %3 cannot be activated.Error code %4
|
18004 |
Channel %1 block %2 orientation of workpiece-related protection zone %3 does not correspond to the orientation of tool-related protection zone %4
|
18005 |
Channel %1 block %2 serious error in definition of NCK-specific protection zone %3
|
18006 |
Channel %1 block %2 serious error in definition of channel-specific protection zone %3
|
18100 |
Channel %1 block %2 invalid value assigned to FXS[]
|
18101 |
Channel %1 block %2 invalid value assigned to FXST[]
|
18102 |
Channel %1 block %2 invalid value assigned to FXSW[]
|
18200 |
Channel %1 block %2 curve table: block search stop not allowed with definition CTABDEF
|
18201 |
Channel %1 block %2 curve table: table %3 does not exist
|
18202 |
Channel %1 block %2 curve table: instruction CTABEND without CTABDEF not allowed
|
18300 |
Channel %1 block %2 frame: fine shift not possible
|
18310 |
Channel %1 block %2 frame: illegal rotation
|
18311 |
Channel %1 block %2 frame: illegal instruction
|
18312 |
Channel %1 block %2 frame: fine shift not configured
|
18313 |
Channel %1 block %2 frame: illegal switchover of geometry axes
|
18314 |
Channel %1 block %2 frame: type conflict
|
18400 |
Channel %1 block %2 language change not possible:
|
20000 |
Channel %1 axis %2 reference cam not reached
|
20001 |
Channel %1 axis %2 no cam signal present
|
20002 |
Channel %1 axis %2 zero mark not found
|
20003 |
Channel %1 axis %2 measuring system error
|
20004 |
Channel %1 axis %2 reference mark missing
|
20005 |
Channel %1 axis %2 reference point approach aborted
|
20006 |
Channel %1 axis %2 reference point creep velocity not reached
|
20007 |
Channel %1 axis %2 reference point approach requires 2 measuring systems
|
20008 |
Channel %1 axis %2 reference point approach requires second referenced measuring system
|
20050 |
Channel %1 axis %2 handwheel mode active
|
20051 |
Channel %1 axis %2 handwheel mode not possible
|
20052 |
Channel %1 axis %2 already active
|
20053 |
Channel %1 axis %2 DRF, FTOCON, external zero point offset not possible
|
20054 |
Channel %1 axis %2 wrong index for indexing axis in JOG mode
|
20055 |
Channel %1 master spindle not present in JOG mode
|
20056 |
Channel %1 axis %2 no revolutional feedrate possible. Axis/spindle %3 stationary
|
20057 |
Channel %1 block %2 revolutional feedrate for axis/spindle %3 is <= zero
|
20058 |
Channel %1 axis %2 revolutional feedrate: illegal feed source
|
20060 |
Channel %1 axis %2 cannot be traversed as geometry axis
|
20061 |
Channel %1 axis %2 cannot be traversed as orientation axis
|
20062 |
Channel %1 axis %2 already active
|
20063 |
Channel %1 axis %2 orientation axes cannot be traversed without transformation
|
20065 |
Channel %1 master spindle not defined for geometry axes in JOG mode
|
20070 |
Channel %1 axis %2 programmed end position is behind software limit switch %3
|
20071 |
Channel %1 axis %2 programmed end position is behind working area limit %3
|
20072 |
Channel %1 axis %2 is not an indexing axis
|
20073 |
Channel %1 axis %2 cannot be repositioned
|
20074 |
Channel %1 axis %2 wrong index position
|
20075 |
Channel %1 axis %2 can currently not oscillate
|
20076 |
Channel %1 axis %2 oscillating – mode change not possible
|
20077 |
Channel %1 axis %2 programmed position is behind software limit switch %3
|
20078 |
Channel %1 axis %2 programmed position is behind working area limit %3
|
20079 |
Channel %1 axis %2 oscillation path length %3 <= 0
|
20080 |
Channel %1 axis %2 no handwheel assigned for overlaid motion
|
20085 |
Channel %1 contour handwheel: traverse direction or overtravel of beginning of block not allowed
|
20090 |
Axis %1 travel to fixed stop not possible. Check programming and axis data.
|
20091 |
Axis %1 has not reached fixed stop
|
20092 |
Axis %1 travel to fixed stop still active
|
20093 |
Axis %1 standstill monitoring at fixed-stop end point has been triggered
|
20094 |
Axis %1 function has been aborted
|
20095 |
Axis %1 illegal torque, current torque %2
|
20096 |
Axis %1 brake test aborted, additional information %2
|
20100 |
Channel %1: invalid configuration for digitizing function
|
20101 |
Communication with the digitizer not possible
|
20102 |
Channel %1: No or invalid trafo at digitizing active
|
20103 |
Channel %1: digitizing module does not support 3+2 axis digitizing
|
20105 |
Channel %1: axes stopped by digitizer. Error code: %2
|
20106 |
Emergency stop set by the digitizer
|
20108 |
Invalid data package received from the digitizer. Error codes: %1, %2
|
20109 |
Error in communication with the digitizer: status code of com-circuit: %1
|
20120 |
Axis %1: too many compensation relations
|
20121 |
Axis %1: Configuration error in compensation table %2
|
20122 |
Compensation table %1: invalid axis assignment
|
20123 |
Axis %1: different output assignment of multiplied tables
|
20124 |
Axis %1: sum of compensation values too large
|
20125 |
Axis %1: change of compensation value is too rapid
|
20130 |
Channel %1 contour tunnel monitoring
|
20140 |
Channel %1 motion synchronous action: traversing of command axis %2 see NC alarm %3
|
20141 |
Channel %1 motion synchronous action: illegal axis type
|
20142 |
Channel %1 command axis %2: rotation of axis container already enabled
|
20143 |
Channel %1 axis %2 command axis cannot be started as it is controlled by the PLC
|
20144 |
Channel %1 block %2 motion synchronous action: system variable access not possible
|
20145 |
Channel %1 block %2 motion synchronous action: arithmetic error
|
20146 |
Channel %1 block %2 motion synchronous action: nesting depth exceeded
|
20147 |
Channel %1 block %2 motion synchronous action: command not executable
|
20148 |
Channel %1 block %2 motion synchronous action: internal error %3
|
20149 |
Channel %1 block %2 motion synchronous action: illegal index
|
20150 |
Channel %1 tool management: PLC terminates interrupted command
|
20160 |
Channel %1 tool management: PLC can terminate only incorrectly aborted commands
|
20170 |
Channel %1 machine data $AC_FIFO invalid
|
20200 |
Channel %1 invalid spindle number %2 with tool fine compensation
|
20201 |
Channel %1 spindle %2 no tool assigned
|
20203 |
Channel %1 no active tool
|
20204 |
Channel %1 PUTFTOC command not allowed with FTOCOF
|
20210 |
Channel %1 block %3 spindle %2 wrong values for centerless grinding
|
20211 |
Channel %1 block %3 spindle %2 support point beyond range limits
|
21600 |
Monitoring for ESR active
|
21610 |
Channel %1 axis %2 encoder %3 frequency limit exceeded
|
21611 |
Channel %1 NC-controlled Extended Stop/Retract triggered
|
21612 |
Channel %1 axis %2 VDI signal ‘Servo enable’ reset during motion
|
21613 |
Axis %1 measuring system changing
|
21614 |
Channel %1 axis %2 hardware limit switch %3
|
21615 |
Channel %1 axis %2 taken from traverse mode to follow-up mode
|
21616 |
Channel %1 block %2 overlaid motion active at transformation switchover
|
21617 |
Channel %1 block %2 transformation does not allow to traverse the pole
|
21618 |
Channel %1 as from block %2 transformation active: overlaid motion too great
|
21619 |
Channel %1 block %2 transformation active: motion not possible
|
21650 |
Channel %1 axis %2 overlaid motion not allowed
|
21660 |
Channel %1 block %2 axis %3 conflict between SYNACT: $AA_OFF and CORROF
|
21665 |
Channel %1 $AA_TOFF cleared
|
21670 |
Channel %1 block %2 illegal change of tool direction with $AA_TOFF active
|
21700 |
Channel %1 block %3 axis %2 touch probe already deflected, edge polarity not possible
|
21701 |
Channel %1 block %3 axis %2 measurement not possible
|
21702 |
Channel %1 block %3 axis %2 measurement aborted
|
21703 |
Channel %1 block %3 axis %2 touch probe not deflected, illegal edge polarity
|
21740 |
Output value at analog output no. %1 has been limited
|
21750 |
Error during output of cam signals via timer
|
21760 |
Channel %1 block %2 too many auxiliary functions programmed
|
21800 |
Channel %1 workpiece setpoint %2 reached
|
22000 |
Channel %1 block %3 spindle %2 change of gear stage not possible
|
22010 |
Channel %1 block %3 spindle %2 actual gear stage differs from requested gear stage
|
22011 |
Channel %1 block %3 spindle %2 change to programmed gear stage not possible
|
22012 |
Channel %1 block %2 leading spindle %3 is in simulation.
|
22013 |
Channel %1 block %2 dependent spindle %3 is in simulation.
|
22014 |
Channel %1 block %2. The dynamics of leading spindle %3 and dependent spindle %4 is too variably
|
22020 |
Channel %1 block %3 spindle %2 gear step change position not reached
|
22040 |
Channel %1 block %3 spindle %2 is not referenced with zero marker
|
22045 |
Block %2 spindle/axis %3 not available in channel %1 because active in channel %4
|
22050 |
Channel %1 block %3 spindle %2 no transition from speed control mode to position control mode
|
22051 |
Channel %1 block %3 spindle %2 reference mark not found
|
22052 |
Channel %1 block %3 spindle %2 no standstill on block change
|
22053 |
Channel %1 block %3 spindle %2 reference mode not supported
|
22054 |
Channel %1 block %3 spindle %2 improper punching signal
|
22055 |
Channel %1 block %3 spindle %2 configured positioning speed is too high
|
22060 |
Channel %1 position control expected for axis/spindle %2
|
22062 |
Channel %1 axis %2 reference point approach: zero marker search velocity (MD) is not reached
|
22064 |
Channel %1 axis %2 reference point approach: zero marker search velocity (MD) is too high
|
22065 |
Channel %1 tool management: Tool motion is not possible, as tool %2 with Duplo no. %3 is not in magazine %4
|
22066 |
Channel %1 tool management: Tool change is not possible, as tool %2 with Duplo no. %3 is not in magazine %4
|
22067 |
Channel %1 tool management: tool change not possible since there is no tool available in tool group %2
|
22068 |
Channel %1 block %2 tool management: no tool available in tool group %3
|
22069 |
Channel %1 block %2 tool management: No tool available in tool group %3, program %4
|
22070 |
TO unit %1 Please change tool T= %2 into magazine. Repeat data backup
|
22071 |
TO unit %1 tool %2 duplo no. %3 is active, but not in the magazine area under consideration
|
22100 |
Channel %1 block %3 spindle %2 chuck speed exceeded
|
22200 |
Channel %1 spindle %2 axis stopped during tapping
|
22250 |
Channel %1 spindle %2 axis stopped during thread cutting
|
22260 |
Channel %1 spindle %2 thread might be damaged
|
22270 |
Channel %1 block %2 maximum velocity of thread axis at position %3 reached
|
22275 |
Channel %1 block %2 zero velocity of thread axis at position %3 reached
|
22280 |
Channel %1 in block %2: Prog. acceleration path too short %3, %4 required
|
22320 |
Channel %1 block %2 PUTFTOCF command could not be transferred
|
22321 |
Channel %1 axis %2 PRESET not allowed during traverse motion
|
22322 |
Channel %1 axis %2 PRESET: illegal value
|
25000 |
Axis %1 hardware fault of active encoder
|
25001 |
Axis %1 hardware fault of passive encoder
|
25010 |
Axis %1 pollution of measuring system
|
25011 |
Axis %1 pollution of passive encoder
|
25020 |
Axis %1 zero mark monitoring of active encoder
|
25021 |
Axis %1 zero mark monitoring of passive encoder
|
25022 |
Axis %1 encoder %2 warning %3
|
25030 |
Axis %1 actual velocity alarm limit
|
25031 |
Axis %1 actual velocity warning limit
|
25040 |
Axis %1 standstill monitoring
|
25042 |
Axis %1 standstill monitoring during torque/force limitation
|
25050 |
Axis %1 contour monitoring
|
25060 |
Axis %1 speed setpoint limitation
|
25070 |
Axis %1 drift value too large
|
25080 |
Axis %1 positioning monitoring
|
25100 |
Axis %1 measuring system switchover not possible
|
25105 |
Axis %1 measuring systems differ considerably
|
25110 |
Axis %1 selected encoder not available
|
25200 |
Axis %1 requested set of parameters invalid
|
25201 |
Axis %1 drive fault
|
25202 |
Axis %1 waiting for drive
|
26000 |
Axis %1 clamping monitoring
|
26001 |
Axis %1 parameterization error: friction compensation
|
26002 |
Axis %1 encoder %2 parameterization error: number of encoder marks
|
26003 |
Axis %1 parameterization error: lead screw pitch
|
26004 |
Axis %1 encoder %2 parameterization error: grid point distance with linear encoders
|
26005 |
Axis %1 parameterization error: output rating
|
26006 |
Axis %1 encoder %2 encoder type/output type %3 not possible
|
26007 |
Axis %1 QEC: invalid coarse step size
|
26008 |
Axis %1 QEC: invalid fine step size
|
26009 |
Axis %1 QEC: memory overflow
|
26010 |
Axis %1 QEC: invalid acceleration characteristic
|
26011 |
Axis %1 QEC: invalid measuring periods
|
26012 |
Axis %1 QEC: feed forward control not active
|
26014 |
Axis %1 machine data %2 invalid value
|
26015 |
Axis %1 machine data %2[%3] invalid value
|
26016 |
Axis %1 machine data %2 invalid value
|
26017 |
Axis %1 machine data %2[%3] invalid value
|
26018 |
Axis %1 setpoint output drive %2 used more than once
|
26019 |
Axis %1 encoder %2 measurement not possible with this controller module
|
26020 |
Axis %1 encoder %2 hardware fault %3 during encoder initialization
|
26022 |
Axis %1 encoder %2 measurement with simulated encoder not possible
|
26024 |
Axis %1 machine data %2 value changed
|
26025 |
Axis %1 machine data %2[%3] value changed
|
26030 |
Axis %1 encoder %2 absolute position lost
|
26031 |
Axis %1 configuration error master-slave
|
26032 |
Axis %1 master-slave not configured
|
26050 |
Axis %1 parameter set change from %2 to %3 not possible
|
26051 |
Channel %1 in block %2 unanticipated stop crossed in continuous path mode
|
26052 |
Channel %1 in block %2: path velocity too high for auxiliary function output
|
26070 |
Channel %1 axis %2 cannot be controlled by the PLC, max. number exceeded
|
26072 |
Channel %1 axis %2 cannot be controlled by the PLC
|
26074 |
Channel %1 switching off PLC control of axis %2 not allowed in the current state
|
26080 |
Channel %1 retraction position of axis %2 not programmed or invalid
|
26081 |
Channel %1 axis trigger of axis %2 was activated, but axis is not PLC- controlled
|
26100 |
Axis %1 drive %2 sign of life missing
|
26101 |
Axis %1 drive %2 communication failure
|
26102 |
Axis %1 drive %2 sign of life missing
|
26105 |
Drive of axis %1 not found
|
26106 |
Encoder %2 of axis %1 not found
|
26110 |
Independent drive stop/retract triggered
|
27000 |
Axis %1 is not safely referenced
|
27001 |
Axis %1 error in a monitoring channel, code %2, values: NCK %3, drive %4
|
27002 |
Axis %1 test stop is running
|
27003 |
Checksum error found: %1 %2
|
27004 |
Axis %1, difference safe input %2, NCK %3, drive %4
|
27005 |
Axis %1 error in data cross check: static actual value difference
|
27006 |
Axis %1 Test ext. pulse deletion running
|
27007 |
Axis %1 acceptance test mode is active
|
27008 |
Axis %1 SW limit switch deactivated
|
27010 |
Axis %1 tolerance for safe standstill exceeded
|
27011 |
Axis %1 safe velocity exceeded
|
27012 |
Axis %1 safe end position exceeded
|
27013 |
Axis %1 safe braking ramp exceeded
|
27020 |
Axis %1 stop E triggered
|
27021 |
Axis %1 stop D triggered
|
27022 |
Axis %1 stop C triggered
|
27023 |
Axis %1 stop B triggered
|
27024 |
Axis %1 stop A triggered
|
27030 |
Axis %1 function not supported on this 611D module
|
27031 |
Axis %1 limit value for safe velocity %2 at gear ratio %3 too large (max. %4)
|
27032 |
Axis %1 checksum error of safe monitoring. Confirmation and re-test required!
|
27033 |
Axis %1 parameterization of MD %2[%3] invalid
|
27034 |
Parameterization of MD %1 invalid
|
27090 |
Error in data cross check NCK-PLC, %1[%2], NCK: %3; %4 ALSI
|
27091 |
Error in data cross check NCK PLC, stop of %1
|
27092 |
Communication broken off during NCK PLC data cross check, error detected by %1
|
27093 |
Checksum error NCK-SPL, %1, %2, %3
|
27094 |
Write access to system variable %1 only allowed from NCK-SPL
|
27095 |
%1 SPL protection not activated
|
27096 |
SPL start not allowed
|
27100 |
At least one axis is not safely referenced
|
27101 |
Axis %1 difference in function safe operational stop, NCK: %2 drive: %3
|
27102 |
Axis %1 difference in function safe velocity %2, NCK: %3 drive: %4
|
27103 |
Axis %1 difference in function safe limit position %2, NCK: %3 drive: %4
|
27104 |
Axis %1 difference in function safe cam plus %2, NCK: %3 drive: %4
|
27105 |
Axis %1 difference in function safe cam minus %2, NCK: %3 drive: %4
|
27106 |
Axis %1 difference in function safe velocity nx, NCK: %2 drive: %3
|
27107 |
Axis %1 difference in function cam modulo monitoring, NCK: %2 drive: %3
|
27124 |
Stop A triggered at least in 1 axis
|
27200 |
PROFIsafe: cycle time %1 [ms] too long
|
27201 |
PROFIsafe: MD %1[%2]: bus segment %3 error
|
27202 |
PROFIsafe: MD %1[%2]: address %3 error
|
27203 |
PROFIsafe: MD %1[%2]: SPL assignment error
|
27204 |
PROFIsafe: double assignment MD %1[%2] – MD %3[%4]
|
27220 |
PROFIsafe: Number of NCK F modules (%1) <> number of DP modules (%2)
|
27221 |
PROFIsafe: NCK F module MD %1[%2] unknown
|
27222 |
PROFI safe: S7 F module PROFI safe address %1 unknown
|
27223 |
PROFIsafe: NCK F module MD %1[%2] is not a %3 module
|
27224 |
PROFIsafe: F module MD %1[%2] – MD %3[%4]: double assignment of PROFIsafe address
|
27225 |
PROFIsafe: slave %1, configuration error %2
|
27240 |
PROFIsafe: DP M not running up, DP info: %1
|
27241 |
PROFIsafe: DP M version different, NCK: %1, PLC: %2
|
27242 |
PROFIsafe: F module %1, %2 faulty
|
27250 |
PROFIsafe: configuration in DP M changed; error code %1 – %2
|
27251 |
PROFIsafe: F module %1, %2 reports error %3
|
27252 |
PROFIsafe: Slave %1, sign-of-life error
|
27253 |
PROFIsafe: communication fault F master component %1, error %2
|
27254 |
PROFIsafe: F module %1, error on channel %2; %3
|
27255 |
PROFIsafe: F module %1, general error
|
27256 |
PROFIsafe: Current cycle time %1 [ms] > parameterized cycle time
|
27299 |
PROFIsafe: Diagnosis %1 %2 %3 %4
|
28000 |
NCU link connection to all other NCUs of the link network has been aborted
|
28001 |
NCU link connection to the NCU %1 of the link network has been aborted
|
28002 |
Error on activation of machine data, NCU network-wide machine data were modified by NCU %1
|
28004 |
NCU link: NCU %1 of the link network is not on the bus
|
28005 |
NCU link: NCU %1 of the link network not running synchronously
|
28007 |
NCU link: conflict in configuration data of NCU %1
|
28008 |
NCU link: conflict in timer setting of NCU %1
|
28009 |
NCU link: conflict in bus parameters of NCU %1
|
28010 |
NCU link: the NCU %1 has not received a message
|
28011 |
IPO time insufficient for NCU link. Link cycle time: %1
|
28012 |
NCU link: synchronization cycle signal failure %1 times
|
28020 |
NCU link: too many link axes configured %1
|
28030 |
Serious alarm on NCU %1, axes in follow-up mode
|
28031 |
Serious alarm on NCU %1 not yet acknowledged, axes still in follow-up mode
|
28032 |
Emergency stop activated on NCU %1, axes in follow-up mode
|
28033 |
Emergency stop on NCU % 1, axes still in follow-up mode
|
29033 |
Channel %1 axis change of axis %2 not possible, PLC axis movement not yet completed
|
60000 |
Channel %1 block %2:
|
61000 |
Channel %1 block %2 no tool compensation active
|
61001 |
Channel %1 block %2 thread lead incorrect
|
61002 |
Channel %1 block %2 machining type wrongly defined
|
61003 |
Channel %1 block %2 no feed programmed in the cycle
|
61004 |
Channel %1 block %2 configuration geometry axis incorrect
|
61005 |
Channel %1 block %2 3rd geometry axis not present
|
61006 |
Channel %1 block %2 tool radius too large
|
61007 |
Channel %1 block %2 tool radius too small
|
61009 |
Channel %1 block %2 active tool number = 0
|
61010 |
Channel %1 block %2 finishing allowance too large
|
61011 |
Channel %1 block %2 scaling not allowed
|
61012 |
Channel %1 block %2 different scaling on the plane
|
61013 |
Channel %1 block %2 basic settings were changed, program cannot be executed
|
61101 |
Channel %1 block %2 reference plane incorrectly defined
|
61102 |
Channel %1 block %2 no spindle direction programmed
|
61103 |
Channel %1 block %2 number of drillings is zero
|
61104 |
Channel %1 block %2 contour violation of slots/long holes
|
61105 |
Channel %1 block %2 cutter radius too large
|
61106 |
Channel %1 block %2 number or distance of circular elements
|
61107 |
Channel %1 block %2 first drilling depth incorrectly defined
|
61108 |
Channel %1 block %2 illegal values for parameters _RAD1 and _DP1
|
61109 |
Channel %1 block %2 parameter _CDIR incorrectly defined
|
61110 |
Channel %1 block %2 finishing allowance at the base > depth infeed
|
61111 |
Channel %1 block %2 infeed width > tool diameter
|
61112 |
Channel %1 block %2 tool radius negative
|
61113 |
Channel %1 block %2 parameter _CRAD for corner radius too large
|
61114 |
Channel %1 block %2 machining direction G41/G42 incorrectly defined
|
61115 |
Channel %1 block %2 approach or retract mode (straight line/circle/plane/space) incorrectly defined
|
61116 |
Channel %1 block %2 approach or retraction path = 0
|
61117 |
Channel %1 block %2 active tool radius <= 0
|
61118 |
Channel %1 block %2 length or width = 0
|
61119 |
Channel %1 block %2 nominal or core diameter incorrectly programmed
|
61120 |
Channel %1 block %2 internal/external thread type not defined
|
61121 |
Channel %1 block %2 number of teeth per cutting edge missing
|
61122 |
Channel %1 block %2 safety clearance on the plane incorrectly defined
|
61124 |
Channel %1 block %2 infeed width is not programmed
|
61125 |
Channel %1 block %2 technology selection in parameter _TECHNO incorrectly defined
|
61126 |
Channel %1 block %2 thread length too short
|
61127 |
Channel %1 block %2 transmission ratio of tapping axis incorrectly defined (machine data)
|
61128 |
Channel %1 block %2 dipping angle = 0 for dipping with oscillation or helix
|
61180 |
Channel %1 block %2 no name assigned to swivel data block, although MD $MN_MM_NUM_TOOL_CARRIER > 1
|
61181 |
Channel %1 block %2 NCK software version unsufficient (missing TOOLCARRIER functionality)
|
61182 |
Channel %1 block %2 name of swivel data block unknown
|
61183 |
Channel %1 block %2 retraction mode GUD7 _TC_FR beyond value range 0… 2
|
61184 |
Channel %1 block %2 no solution possible with current input angle values
|
61185 |
Channel %1 block %2 no or incorrect (min > max) rotary axis angle ranges assigned
|
61186 |
Channel %1 block %2 rotary axis vectors invalid –> Check installation and start-up of the swivel cycle CYCLE800
|
61188 |
Channel %1 block %2 no axis name for the 1st axis assigned -> Check installation and start-up of the swivel cycle CYCLE800
|
61200 |
Channel %1 block %2 too many elements in the machining block
|
61201 |
Channel %1 block %2 wrong sequence in the machining block
|
61202 |
Channel %1 block %2 no technology cycle
|
61203 |
Channel %1 block %2 no positioning cycle
|
61204 |
Channel %1 block %2 unknown technology cycle
|
61205 |
Channel %1 block %2 unknown positioning cycle
|
61210 |
Channel %1 block %2 block search element not found
|
61211 |
Channel %1 block %2 absolute reference missing
|
61212 |
Channel %1 block %2 wrong tool type
|
61213 |
Channel %1 block %2 circle radius too small
|
61214 |
Channel %1 block %2 no lead programmed
|
61215 |
Channel %1 block %2 raw dimension incorrectly programmed
|
61216 |
Channel %1 block %2 feed/tooth only possible with milling tools
|
61217 |
Channel %1 block %2 cutting speed for tool radius 0 programmed
|
61218 |
Channel %1 block %2 feed/tooth programmed, but number of teeth is zero
|
61222 |
Channel %1 block %2 plane infeed greater than the tool diameter
|
61223 |
Channel %1 block %2 approach path too short
|
61224 |
Channel %1 block %2 retract path too short
|
61225 |
Channel %1 block %2 swivel data block unknown
|
61226 |
Channel %1 block %2 swivel head cannot be exchanged
|
61230 |
Channel %1 block %2 tool probe diameter too small
|
61231 |
Channel %1 block %2 ShopMill program %3 cannot be executed, as it has not been tested by ShopMill
|
61232 |
Channel %1 block %2 loading of magazine tool not possible
|
61233 |
Channel %1 block %2: Thread inclination incorrectly defined
|
61234 |
Channel %1 block %2 ShopMill subroutine %4 cannot be executed, as it has not been tested by ShopMill
|
61235 |
Channel %1 block %2: ShopTurn program %4 cannot be executed, as it has not been tested by ShopTurn.
|
61236 |
Channel %1 block %2: ShopTurn subroutine %4 cannot be executed, as it has not been tested by ShopTurn.
|
61237 |
Channel %1 block %2: Retraction direction unknown. Manually retract tool!
|
61238 |
Channel %1 block %2: Machining direction unknown.
|
61239 |
Channel %1 block %2: Tool change point lies in the retraction area!
|
61240 |
Channel %1 block %2: Wrong feed type
|
61241 |
Channel %1 block %2: No retraction plane defined for this machining direction.
|
61242 |
Channel %1 block %2: Wrong machining direction
|
61243 |
Channel %1 block %2: Correct tool change point, tool tip is in retraction area!
|
61244 |
Channel %1 block %2: Thread lead change results in an undefined thread
|
61246 |
Channel %1 block %2: Safety clearance too small
|
61247 |
Channel %1 block %2: Blank radius too small
|
61248 |
Channel %1 block %2: Infeed too small
|
61249 |
Channel %1 block %2: Number of edges too small
|
61250 |
Channel %1 block %2: Key width/Edge length too small
|
61251 |
Channel %1 block %2: Key width/Edge length too large
|
61252 |
Channel %1 block %2: Chamfer/Radius too large
|
61253 |
Channel %1 block %2: No finishing allowance programmed
|
61254 |
Channel %1 block %2: Error when traversing to fixed stop
|
61255 |
Channel %1 block %2: Cut-off error: Tool breakage?
|
61301 |
Channel %1 block %2 measuring probe does not switch
|
61302 |
Channel %1 block %2 measuring probe collision
|
61303 |
Channel %1 block %2 safe area exceeded
|
61308 |
Channel %1 block %2 check measuring distance 2a
|
61309 |
Channel %1 block %2 check measuring probe type
|
61310 |
Channel %1 block %2 scale factor is active
|
61311 |
Channel %1 block %2 no D number is active
|
61316 |
Channel %1 block %2 center point and radius cannot be determined.
|
61332 |
Channel %1 block %2 change tool tip position
|
61338 |
Channel %1 block %2 positioning velocity is zero
|
61601 |
Channel %1 block %2 finished-part diameter too small
|
61602 |
Channel %1 block %2 tool width incorrectly defined
|
61603 |
Channel %1 block %2 groove form incorrectly defined
|
61604 |
Channel %1 block %2 active tool violates programmed contour
|
61605 |
Channel %1 block %2 contour incorrectly programmed
|
61606 |
Channel %1 block %2 contour processing error
|
61607 |
Channel %1 block %2 starting point incorrectly programmed
|
61608 |
Channel %1 block %2 wrong cutting edge position programmed
|
61609 |
Channel %1 block %2 form incorrectly defined
|
61610 |
Channel %1 block %2 no infeed depth programmed
|
61611 |
Channel %1 block %2 no intersection point found
|
61612 |
Channel %1 block %2 thread axis cutting not possible
|
61613 |
Channel %1 block %2 undercut position incorrectly defined
|
61800 |
Channel %1 block %2: External CNC system missing
|
61801 |
Channel %1 block %2: Wrong G code selected
|
61802 |
Channel %1 block %2: Wrong axis type
|
61803 |
Channel %1 block %2 programmed axis not present
|
61804 |
Channel %1 block %2: Progr. position exceeds reference point
|
61805 |
Channel %1 block %2: The value is absolutely and incrementally programmed
|
61806 |
Channel %1 block %2: Incorrect axis assignment
|
61807 |
Channel %1 block %2 wrong spindle direction programmed (active)
|
61808 |
Channel %1 block %2: The final drilling depth or individual drilling depth is missing
|
61809 |
Channel %1 block %2: Impermissible drilling position
|
61810 |
Channel %1 block %2: ISO-G code not possible
|
61811 |
Channel %1 block %2: Impermissible ISO axis name
|
61812 |
Channel %1 block %2: Value(s) in the external cycle call incorrectly defined
|
61813 |
Channel %1 block %2: GUD value incorrectly defined
|
61814 |
Channel %1 block %2: Polar coordinates not possible with cycle
|
61815 |
Channel %1 block %2: G40 not active
|
61816 |
Channel %1 block %2: axes are not at the reference point
|
61817 |
Channel %1 block %2: The axis coordinates are within the protection zone
|
61818 |
Channel %1 block %2: The axis area limit values are identical
|
62000 |
Channel %1 block %2:
|
62100 |
Channel %1 block %2 no drilling cycle active
|
62101 |
Channel %1 block %2: Incorrect cutting direction – G3 is generated
|
62103 |
Channel %1 block %2: The finishing allowance is not programmed
|
62105 |
Channel %1 block %2 number of columns or lines is zero
|
62180 |
Channel %1 block %2 no name assigned to swivel data block although machine data $MN_MM_NUM_TOOL_CARRIER > 1
|
62181 |
Channel %1 block %2 NCK software version unsufficient (missing TOOLCARRIER functionality)
|
62182 |
Channel %1 block %2: Load swivel head
|
62183 |
Channel %1 block %2 retraction mode GUD7 _TC_FR beyond value range 0…2
|
62184 |
Channel %1 block %2 no solution possible with current input angle values
|
62185 |
Channel %1 block %2 no end stop assigned to rotary axes
|
62186 |
Channel %1 block %2 illegal rotary axis vectors
|
62187 |
Channel %1 block %2 name of swivel data block unknown
|
62200 |
Channel %1 block %2: Start spindle
|
63000 |
Channel %1 block %2:
|
65000 |
Channel %1 block %2:
|
66000 |
Channel %1 block %2:
|
67000 |
Channel %1 block %2:
|
68000 |
Channel %1 block %2:
|
70000 |
Compile cycle alarm
|
75000 |
OEM alarm
|
75005 |
Channel %1 block %2 CLC: General programming error
|
75010 |
Channel %1 block %2 CLC_LIM value exceeds MD limit
|
75015 |
Channel %1 block %2 CLC(0) with active TOC
|
75016 |
Channel %1 block %2 CLC: orientation changed for TRAFOOF
|
75020 |
Channel %1 CLC position offset at lower limit %2
|
75021 |
Channel %1 CLC position offset at upper limit %2
|
75025 |
Channel %1 CLC stopped because sensor head has been touched
|
75050 |
Channel %1 wrong MD configuration, error code %2
|
75051 |
Channel %1 CC_COPON CC_COPOFF error code %2
|
75060 |
Channel %1 tolerance window exceeded axis %2
|
75061 |
Channel %1 coupling active axis %2
|
75062 |
Channel %1 axes not in standstill axis %2
|
75070 |
Channel %1 wrong machine data for collision protection %2
|
75071 |
Channel %1 collision monitoring axis %2
|
75100 |
Too many analog axes configured
|
75110 |
Axis %1 reached drift limit
|
75200 |
Channel %1 wrong MD configuration, %2 incorrect
|
75210 |
Channel %1 number of axes/axis assignment inconsistent
|
75250 |
Channel %1 tool parameters incorrect
|
75255 |
Channel %1 working area error
|
75260 |
Channel %1 block %2 tool parameters incorrect
|
75265 |
Channel %1 block %2 working area error
|
75270 |
Channel %1 tool parameters incorrect
|
75275 |
Channel %1 block %2 working area error
|
75451 |
Error with definition of setpoint switchover
|
75452 |
Axis %1 setpoint switchover not possible in the current state
|
75500 |
Channel %1 wrong configuration
|
75600 |
Channel %1 retrace support: wrong MD configuration. Error code %2
|
75601 |
Channel %1 block %2 invalid parameter in CC_PREPRE()
|
75605 |
Channel %1 retrace support: internal error, error code %2
|
75606 |
Channel %1 retraceable contour was shortened
|
75607 |
Channel %1 resynchronisation not possible
|
100300 |
xxx not found
|
100301 |
The table cannot be completely generated
|
100302 |
No data available – or no access authorization
|
100303 |
Paging not possible
|
100350 |
Display MD saved
|
100351 |
Display MD take-over not possible
|
101000 |
No connection to the PLC!
|
101001 |
The PLC system status list cannot be read!
|
101002 |
Invalid password!
|
101003 |
Password for %1 is set!
|
101004 |
Password for %1 is set!
|
101005 |
The passwords do not match!
|
101006 |
Password is deleted!
|
101007 |
Password is not set!
|
101008 |
Current access level: %1
|
101013 |
Input error – see help – (i)-key
|
101016 |
Error: The operand address is greater than 65535!
|
101017 |
No PLC input screen forms found!
|
101018 |
Reading-in only possible in an active PLC status!
|
101100 |
No access authorization!
|
101111 |
No axes configured!
|
101112 |
No drives configured!
|
101113 |
No channels configured!
|
101114 |
No MSD configured!
|
101115 |
No FDD configured!
|
101130 |
Error return value not defined: 00h 00h
|
101131 |
No servo disable at PI start
|
101132 |
Impermissible execution argument value
|
101133 |
MDx120 CURRCTRL_GAIN could not be calculated
|
101134 |
MDx407 SPEEDCTRL_GAIN_1 could not be calculated
|
101135 |
MDx409 SPEEDCTRL_INTEGRATOR_TIME_1 could not be calculated
|
101136 |
MDx150 FIELDCTRL_GAIN could not be calculated
|
101137 |
MDx141 MAGNETIZING_REACTANCE=0
|
101138 |
MDx139/MDx140 MD_STATOR-/ROTOR_LEAKAGE_REACTANCE=0
|
101139 |
MDx134 MOTOR_NOMINAL_FREQUENCY=0
|
101140 |
MDx138 ROTOR_COLD_RESISTANCE = 0
|
101141 |
MDx117 MOTOR_INERTIA = 0
|
101142 |
MDx146 < MDx142 MOTOR_MAX_ALLOWED_SPEED < FIELD_WEAKENING_SPEED
|
101143 |
MDx142 FIELD_WEAKENING_SPEED = 0
|
101144 |
MDx118 MOTOR_STANDSTILL_CURRENT = 0
|
101145 |
MD1104/1118 MOTOR_MAX_CURRENT/MOTOR_STANDSTILL_CURRENT > 900.0
|
101146 |
Boot file(s) saved
|
101147 |
Boot file(s) deleted
|
101148 |
Controller MD calculated
|
101150 |
MD set active
|
101151 |
Start-up successful
|
101153 |
MMC-NCK communication faulty %1 %2
|
101154 |
PI service was rejected
|
101155 |
Path %1 not available
|
101156 |
Impermissible function
|
101157 |
File %1 not available
|
101158 |
Function not permitted in the current operating state.
|
101159 |
Remote block in wrong state
|
101160 |
Date and time of the PLC set
|
101161 |
The drive is not in cyclic mode!
|
101162 |
MDx134/MDx400 MOTOR_NOMINAL_FREQUENCY/MOTOR_RATED_SPEED impermissible
|
101163 |
MDx130 MOTOR_NOMINAL_POWER <= 0
|
101164 |
MDx132 MOTOR_NOMINAL_VOLTAGE <= 0
|
101165 |
MDx103 MOTOR_NOMINAL_CURRENT <= 0
|
101166 |
MDx129 POWER_FACTOR_COS_PHI impermissible
|
101167 |
MDx134/MDx400 MOTOR_NOMINAL_FREQUENCY/MOTOR_RATED_SPEED impermissible
|
101168 |
Warning MDx142 FIELD_WEAKENING_SPEED < MDx400 MOTOR_RATED_SPEED
|
101200 |
Safety-Integrated data copied
|
101201 |
Safety-Integrated data confirmed
|
101202 |
SI data is copied from axis %1 to drive %2 Parameters: %1 = Axis name %2 = Drive number
|
101203 |
SI data not completely copied
|
101204 |
SI data not confirmed
|
101205 |
Drive data changed? -> Don’t forget to save the boot files!
|
101206 |
Search action running, pleas wait
|
101207 |
Position at $MN_
|
101208 |
SI data confirmed: Axis 1
|
101209 |
SI data confirmed: Drive 1
|
101210 |
The machine data is being prepared for display
|
101211 |
NCK address not changed!
|
101212 |
NCK address changed!
|
101213 |
Invalid NCK address.
|
101214 |
Initialization of this window failed!
|
101300 |
Please wait – language is being changed
|
103000 |
There is no correction block on the NCK
|
103001 |
Selection is only possible after being enabled or in the RESET state.
|
103002 |
Copying to the clipboard is not possible
|
103003 |
MDI clipboard cannot be deleted
|
103004 |
Block search not possible
|
103006 |
Block search without calculation only possible on the main program level.
|
103007 |
Ending overstore is not possible in this channel state.
|
103008 |
Block search in channel %1 started – please wait
|
103009 |
Conflict between search type and search target!
|
103010 |
Invalid file name
|
103011 |
No program selected – block search finished
|
103014 |
Please reference the axis first
|
104000 |
Current tool not found
|
104001 |
No other tools available
|
104002 |
No other cutting edges available
|
104003 |
There aren’t any tools at all
|
104004 |
No tool selected
|
104005 |
No cutting edge selected
|
104006 |
No TO area available in the current channel
|
104007 |
Error during tool creation
|
104008 |
Error during cutting edge creation
|
104011 |
Error during tool deletion
|
104012 |
No master spindle available
|
104014 |
Incorrect entry
|
104015 |
Number of parameters per cutting edge is zero
|
104016 |
No spindle available
|
104018 |
Tool not available
|
104019 |
Tool type not available
|
104020 |
No empty location found
|
104023 |
Error during tool loading
|
104024 |
Error during tool unloading
|
104025 |
No magazine configured
|
104026 |
Notice: Tool is being loaded!
|
104027 |
Notice: Tool is being unloaded!
|
104029 |
Loading to this location not possible
|
104030 |
No more data available
|
105000 |
Error x y
|
105001 |
Cycle description sc.com not available
|
105002 |
File xxx already exists
|
105003 |
Workpiece xxx already exists
|
105004 |
Clipboard empty! To PASTE, COPY first
|
105005 |
Only workpieces can be inserted here
|
105006 |
Only files can be inserted here
|
105007 |
No name specified
|
105008 |
Memory error while writing a cycle call
|
105009 |
No write-authorization for the data
|
105010 |
No data selected
|
105011 |
Cycle description cov.com not available
|
105012 |
The program is not or only partially editable (NC reset)
|
105013 |
The copied data can be inserted with the soft key “Paste”
|
105014 |
Error while copying!
|
105015 |
Error while renaming!
|
105016 |
Error while deleting!
|
105017 |
Selection is only possible after being enabled or in the RESET state.
|
105018 |
Error during program generation!
|
105019 |
Error while opening a window!
|
105020 |
Error while closing a window!
|
105021 |
Error during workpiece generation!
|
105022 |
Error during enabling!
|
105023 |
File exists already!
|
105024 |
Check values! – At least 1 value lies outside the input limits!
|
105025 |
Please wait, the directory is being prepared!
|
105026 |
Notice! The simulated program and edited program are not the same!
|
105030 |
Please wait, renumbering is being carried out!
|
105031 |
Renumbering was aborted!
|
105032 |
Renumbering finished!
|
105041 |
Block number is too large!
|
105042 |
Impermissible block number!
|
105043 |
Impermissible increment!
|
105050 |
Please wait: Graphic is being output!
|
105051 |
Output of dynamic long texts for cycle parameterization
|
105052 |
Error in the cycle description of the !
|
105053 |
No cycle available in current line!
|
105054 |
Error during cycle description call!
|
105060 |
Please wait: Initilization of the cycle support
|
105061 |
Error when opening the file!
|
105062 |
Error when closing the file!
|
105063 |
Error when positioning in the file %1!
|
105064 |
Error when reading the file!
|
105070 |
Please wait: Initialization of the simulation started!
|
105075 |
Not enough axes in the current channel? > Contour with default axis names: X, Z !
|
109001 |
No switchover: Switchover disable set in current PLC
|
109002 |
No switchover: Target PLC occupied, try again
|
109003 |
No switchover: Switchover disable set in target PLC
|
109004 |
No switchover: PLC occupied by higher-priority MMC’s
|
109005 |
No switchover: No displaceable MMC at the target PLC
|
109006 |
No switchover: Selected channel invalid
|
109007 |
Channel switchover running
|
109008 |
Activation is running
|
111001 |
Non-interpretable step in line %1
|
111002 |
Insufficient memory, abort in line %1
|
111003 |
ManualTurn: %1
|
111004 |
File faulty or not available: %1
|
111005 |
Error when interpreting the contour %1 Parameters: %1 = Contour name
|
111006 |
Maximum number of contour elements exceeded %1
|
111007 |
Error in line %1 %2
|
111008 |
Spindle not synchronized
|
111009 |
Load new tool: T%1 Parameters: %1 = Tool number
|
111010 |
Teach-in interruption: Log overflow
|
111100 |
Wrong position programmed for the spindle
|
111105 |
No measuring system available
|
111106 |
No spindle stop for a block change
|
111107 |
Reference mark not found
|
111108 |
No transition from speed control mode to position control mode
|
111109 |
Configured positioning velocity is too high
|
111110 |
Velocity/Speed is negative
|
111111 |
Setpoint speed is zero
|
111112 |
Invalid gear stage
|
111115 |
Programmed position was not reached
|
111126 |
Absolute value minus not possible
|
111127 |
Absolute value plus not possible
|
111200 |
Spindle positioning error
|
111300 |
NC start key defective
|
111301 |
NC stop key defective
|
111302 |
Spindle start key defective
|
111303 |
Spindle stop key defective
|
111304 |
Connection to the PLC broken off
|
111305 |
Asynchronous subroutine was not executed
|
111306 |
Error when selecting or deselecting constant cutting speed
|
111307 |
Error when deleting handwheel offset
|
111308 |
Error when setting upper spindle speed limit
|
111309 |
Error when selecting tool
|
111310 |
Error when selecting zero offset
|
111311 |
NC start not possible: Deselect single block
|
111400 |
Unknown PLC error
|
111410 |
Tool %1 was created
|
111411 |
%1 Tool(s) can (could) not be created
|
111420 |
Error during the inch/metric conversion! Check all data!
|
111430 |
Program not loaded. Error when converting old cycles in G code. No NC memory.
|
111900 |
Start only possible in basic display
|
111901 |
Contour is contained in the current program, machining not enabled
|
111902 |
Start only with valid reference point
|
111904 |
4. Axis not configured, i.e., no driven tool possible
|
112045 |
Several insertion points required
|
112046 |
Main contour cannot be bypassed
|
112052 |
No residual material generated
|
112057 |
Programmed helix violates contour
|
112099 |
System-error contour pocket
|
112100 |
Error during renumbering. Original state restored.
|
112200 |
The contour is a step in the current program sequence. Machining not enabled
|
112201 |
The contour is a step in the current automatic sequence. Machining not enabled
|
112210 |
Tool axis cannot be switched over. Insufficient NC memory.
|
112211 |
Tool preselection could not be processed. Insufficient NC memory.
|
112300 |
Tool management type 2 not possible. Magazine not completely loaded.
|
112301 |
Tool management type 2 not possible. The magazine is not sorted as in the tool list.
|
112323 |
Replace swivel head.
|
112324 |
Load swivel head.
|
112325 |
Exchange swivel head.
|
112326 |
Set swivel head
|
112327 |
Angle not in permissible area
|
112328 |
Angle adapted to angle grid.
|
112329 |
Set swivel head/table
|
112330 |
Set swivel table.
|
112350 |
No swivel data set up.
|
112360 |
The step was not accepted into the program sequence, as the program is running.
|
112400 |
Is not available in the tool management
|
112401 |
Tool could not be created
|
112420 |
Error during the inch/metric conversion! Check all data!
|
112502 |
Insufficient memory, abort in line %1
|
112504 |
File faulty or not available: %1 Parameters: %1 = File name
|
112505 |
Error when interpreting the contour %1
|
112506 |
Maximum number of contour elements exceeded %1
|
112541 |
Program cannot be interpreted
|
112604 |
Connection to the PLC broken off
|
112605 |
Asynchronous subroutine was not executed
|
112650 |
Unknown PLC error
|
112999 |
Faulty grafic data. Exit graphic and restart
|
120000 |
Area %1 cannot be loaded! Acknowledge alarm, press area switchover key!
|
120001 |
Area %1 cannot be selected. Please deactivate area %2
|
120002 |
Area %1 is still active. Please deactivate area %1
|
120003 |
Area %1 cannot be deactivated. Please try again
|
120005 |
Please acknowledge the dialog box in area %1
|
120006 |
The channel switchover is currently disabled by area %1.
|
120007 |
The channel switchover is currently disabled.
|
120008 |
Control unit switchover, PLC timeout: 001 control unit switchover, PLC timeout: 002 control unit switchover, PLC timeout: 003
|
120120 |
The alarm list is full of alarm texts: Number of alarm texts too high Alarm texts: File %1 not found alarm texts: Input/Output error in file %1 alarm texts: Input/Output error alarm texts: Error when reading from the index file alarm texts: Error when writing in the index file alarm texts: Syntax error in alarm text file %1
|
120200 |
Image preparation suppressed
|
120201 |
Communication failure
|
120202 |
Waiting for a connection to the NC
|
120301 |
Faulty entry for hardkey ‘Program’ in Keys.ini.
|
120302 |
The selection is not possible. A program has to have been edited first via the area ‘Program’.
|
120303 |
The selection is not possible. The edited file %1 no longer exists.
|
120304 |
The selection is not possible. The file %1 has insufficient read rights.
|
120305 |
Selection is not possible. The file %1 is currently being edited.
|
120306 |
The selection is not possible. The file %1 is selected and active in channel %2.
|
120307 |
The file %1 cannot be opened for the editor because it is selected in channel %2 for execution from external sources.
|
120308 |
In the event of an emergency stop, the program %1 can only be changed in the machine/program correction area.
|
120309 |
The selection is not possible. Please close the simulation and repeat the selection.
|
120310 |
The selection is not possible. Please wait for the pending action or terminate it, then repeat the selection.
|
300000 |
Hardware drive bus: DCM not present
|
300001 |
Axis %1 drive number %2 not possible
|
300002 |
Axis %1 drive number %2 assigned twice
|
300003 |
Axis %1 drive %2 wrong module type %3
|
300004 |
Axis %1 drive %2 wrong drive type %3 (FDD/MSD)
|
300005 |
At least one module found on drive bus that has not been configured
|
300006 |
Module with drive number %1 has not been found on drive bus
|
300007 |
Axis %1 drive %2 not present or inactive
|
300008 |
Axis %1 drive %2 measuring circuit %3 is not available
|
300009 |
Axis %1 drive %2 measuring circuit %3 wrong measuring circuit type (type %4 used)
|
300010 |
Axis %1 drive %2 active without NC axis assignment
|
300011 |
Axis %1 drive %2 hardware version of spindle not supported
|
300012 |
Axis %1 drive %2 hardware version of control module not supported
|
300020 |
Drive %1 removed for diagnosis
|
300100 |
Drive power failure
|
300101 |
Bus communications failure
|
300200 |
Drive bus hardware fault
|
300201 |
Axis %1 drive %2 timeout during access, error location %3
|
300202 |
Axis %1 drive %2 CRC error, error location %3
|
300300 |
Axis %1 drive %2 boot error, error code %3
|
300400 |
Axis %1 drive %2 system error, error codes %3, %4
|
300401 |
Drive software for type %1, block %2 missing or incorrect
|
300402 |
System error in drive link. Error codes %1, %2
|
300403 |
Axis %1 drive %2 drive software and drive MD with different version numbers
|
300404 |
Axis %1 drive %2 drive MD contains different drive number
|
300405 |
Axis %1 drive %2 unknown drive alarm, code %3
|
300410 |
Axis %1 drive %2 error when storing a file (%3, %4)
|
300411 |
Axis %1 drive %2 error when reading a file (%3, %4)
|
300412 |
Error when storing a file (%1, %2)
|
300413 |
Error when reading a file (%1, %2)
|
300423 |
Measuring results could not be read (%1)
|
300500 |
Axis %1 drive %2 system error, error codes %3, %4
|
300501 |
Axis %1 drive %2 maximum current monitoring
|
300502 |
Axis %1 drive %2 maximum current monitoring of phase current R
|
300503 |
Axis %1 drive %2 maximum current monitoring of phase current S
|
300504 |
Axis %1 drive %2 measuring circuit error of motor measuring system
|
300505 |
Axis %1 drive %2 measuring circuit error of absolute track, code %3
|
300506 |
Axis %1 drive %2 NC sign-of-life failure
|
300507 |
Axis %1 drive %2 synchronization error of rotor position
|
300508 |
Axis %1 drive %2 zero mark monitoring of motor measuring system
|
300509 |
Axis %1 drive %2 current frequency exceeded
|
300510 |
Axis %1 drive %2 error on actual current measurement zero balancing
|
300511 |
Axis %1 drive %2 measuring function active
|
300515 |
Axis %1 drive %2 power section heat sink temperature exceeded
|
300604 |
Axis %1 drive %2 motor encoder is not adjusted
|
300605 |
Axis %1 drive %2 motor change not valid
|
300606 |
Axis %1 drive %2 flux controller at limit
|
300607 |
Axis %1 drive %2 current controller at limit
|
300608 |
Axis %1 drive %2 speed controller at limit
|
300609 |
Axis %1 drive %2 encoder cut-off frequency exceeded
|
300610 |
Axis %1 drive %2 rotor position identification failed
|
300611 |
Axis %1 drive %2 generator mode: Motion at rotor position identification
|
300612 |
Axis %1 drive %2 illegal current during rotor position identification
|
300613 |
Axis %1 drive %2 maximum permissible motor temperature exceeded
|
300614 |
Axis %1 drive %2 time monitoring of motor temperature
|
300701 |
Axis %1 drive %2 start-up required
|
300702 |
Axis %1 drive %2 base cycle time invalid
|
300703 |
Axis %1 drive %2 current cycle time invalid
|
300704 |
Axis %1 drive %2 speed controller cycle time invalid
|
300705 |
Axis %1 drive %2 position controller cycle time invalid
|
300706 |
Axis %1 drive %2 monitoring cycle time invalid
|
300707 |
Axis %1 drive %2 basic cycle times of axes differ
|
300708 |
Axis %1 drive %2 current controller cycle times of axes differ
|
300709 |
Axis %1 drive %2 speed controller cycle times of axes differ
|
300710 |
Axis %1 drive %2 position controller cycle times of axes differ
|
300711 |
Axis %1 drive %2 monitoring cycle times of axes differ
|
300712 |
Axis %1 drive %2 configuration of controller structure (higher dynamic response) not possible
|
300713 |
Axis %1 drive %2 lead time for position controller invalid
|
300714 |
Axis %1 drive %2 power section code invalid
|
300715 |
Axis %1 drive %2 maximum power section current less than or equal to zero
|
300716 |
Axis %1 drive %2 torque constant less than or equal to zero
|
300717 |
Axis %1 drive %2 motor moment of inertia less than or equal to zero
|
300718 |
Axis %1 drive %2 calculation dead time of current controller less than or equal to zero
|
300719 |
Axis %1 drive %2 motor not parameterized for delta operation
|
300720 |
Axis %1 drive %2 maximum motor speed invalid
|
300721 |
Axis %1 drive %2 zero-load current greater than rated motor current
|
300722 |
Axis %1 drive %2 zero-load motor current greater than rated current of power section
|
300723 |
Axis %1 drive %2 STS configuration of axes differ
|
300724 |
Axis %1 drive %2 number of pole pairs invalid
|
300725 |
Axis %1 drive %2 number of encoder marks of measuring system invalid
|
300726 |
Axis %1 drive %2 voltage constant is zero
|
300727 |
Axis %1 drive %2 reactance less than or equal to zero
|
300728 |
Axis %1 drive %2 adaption factor torque/current too high
|
300729 |
Axis %1 drive %2 motor zero-speed current less than or equal to zero
|
300730 |
Axis %1 drive %2 rotor resistance invalid
|
300731 |
Axis %1 drive %2 rated power less than or equal to zero
|
300732 |
Axis %1 drive %2 rated speed less than or equal to zero
|
300733 |
Axis %1 drive %2 zero load voltage invalid
|
300734 |
Axis %1 drive %2 zero load current less than or equal to zero
|
300735 |
Axis %1 drive %2 field weakening speed invalid
|
300736 |
Axis %1 drive %2 Lh characteristic invalid
|
300737 |
Axis %1 drive %2 configuration of two EnDat encoders not possible
|
300738 |
Axis %1 drive %2 module number for measuring system not possible
|
300739 |
Axis %1 drive %2 measuring system already used as motor measuring system
|
300740 |
Axis %1 drive %2 measuring system used several times
|
300741 |
Axis %1 drive %2 asynchronous mode: feedforward control gain out of range
|
300742 |
Axis %1 drive %2 voltage/frequency mode: converter frequency invalid
|
300743 |
Axis %1 drive %2 function not supported on this 611D controller module
|
300744 |
Axis %1 drive %2 safety monitoring checksum invalid, confirmation and acceptance test required!
|
300745 |
Axis %1 drive %2 limit values for safe end positions exchanged
|
300746 |
Axis %1 drive %2 SBH/SG not enabled
|
300747 |
Axis %1 drive %2 monitoring cycle time MD 1300 invalid
|
300748 |
Axis %1 drive %2 monitoring cycle times of both axes differ
|
300749 |
Axis %1 drive %2 conversion factor between motor and load too large
|
300750 |
Axis %1 drive %2 parameterization error in speed control adaption
|
300751 |
Axis %1 drive %2 speed control gain too high
|
300752 |
Axis %1 drive %2 blocking frequency of setpoint current filter too high
|
300753 |
Axis %1 drive %2 rotor position identification current less than minimal value
|
300754 |
Axis %1 drive %2 signal number of var. signaling function invalid
|
300755 |
Axis %1 drive %2 voltage/frequency mode: motor is turning
|
300756 |
Axis %1 drive %2 speed hysteresis of setpoint current smoothing invalid
|
300757 |
Axis %1 drive %2 adaption factor of torque limit invalid
|
300757 |
Axis %1 drive %2 adaption factor of torque limit invalid
|
300758 |
Axis %1 drive %2 generator mode: response voltage > switch-off threshold
|
300759 |
Axis %1 drive %2 generator mode: response voltage > monitoring threshold
|
300760 |
Axis %1 drive %2 generator mode: emergency retraction speed > max. motor speed
|
300761 |
Axis %1 drive %2 generator mode: minimum axis speed > max. motor speed
|
300762 |
Axis %1 drive %2 emergency retraction mode/generator mode already active
|
300763 |
Axis %1 drive %2 emergency retraction mode/generator mode invalid
|
300764 |
Axis %1 drive %2 emergency retraction mode/generator mode not possible
|
300765 |
Axis %1 drive %2 measurement of DC link voltage not possible
|
300766 |
Axis %1 drive %2 blocking frequency > Shannon frequency
|
300767 |
Axis %1 drive %2 natural frequency > Shannon frequency
|
300768 |
Axis %1 drive %2 numerator bandwidth > double blocking frequency
|
300769 |
Axis %1 drive %2 denominator bandwidth > double natural frequency
|
300770 |
Axis %1 drive %2 format error
|
300771 |
Axis %1 drive %2 asynchronous mode: converter frequency invalid
|
300772 |
Axis %1 drive %2 asynchronous mode: speed control gain too high
|
300773 |
Axis %1 drive %2 asynchronous mode: feedforward control structure not possible
|
300774 |
Axis %1 drive %2 asynchronous mode: changeover speed invalid
|
300775 |
Axis %1 drive %2 fixed link voltage of axes differ
|
300776 |
Axis %1 drive %2 measuring circuit monitoring must be active
|
300777 |
Axis %1 drive %2 rotor position identification current too high
|
300778 |
Axis %1 drive %2 generator mode: converter frequency rotor position identification
|
300779 |
Axis %1 drive %2 motor moment of inertia less than or equal to zero
|
300780 |
Axis %1 drive %2 zero load current > rated motor current
|
300781 |
Axis %1 drive %2 zero load current > rated current of power section
|
300782 |
Axis %1 drive %2 reactance less than or equal to zero
|
300783 |
Axis %1 drive %2 rotor resistance invalid
|
300784 |
Axis %1 drive %2 zero load voltage invalid
|
300785 |
Axis %1 drive %2 zero load current less than or equal to zero
|
300786 |
Axis %1 drive %2 field weakening speed invalid
|
300787 |
Axis %1 drive %2 asynchronous mode: feedforward control gain out of range
|
300788 |
Axis %1 drive %2 parameterization error in current control adaption
|
300789 |
Axis %1 drive %2 function not supported on this 611D controller module
|
300799 |
Axis %1 drive %2 data backup and reboot required
|
300850 |
Axis %1 drive %2 parameterization error in speed control adaption
|
300854 |
Axis %1 drive %2 signal number of var. signaling function invalid
|
300855 |
Axis %1 drive %2 voltage/frequency mode: motor is turning
|
300858 |
Axis %1 drive %2 generator mode: response voltage > switch-off threshold
|
300859 |
Axis %1 drive %2 generator mode: response voltage > monitoring threshold
|
300860 |
Axis %1 drive %2 generator mode: emergency retraction speed > max. motor speed
|
300861 |
Axis %1 drive %2 generator mode: minimum axis speed > max. motor speed
|
300862 |
Axis %1 drive %2 emergency retraction mode/generator mode already active
|
300863 |
Axis %1 drive %2 emergency retraction mode/generator mode invalid
|
300864 |
Axis %1 drive %2 emergency retraction mode/generator mode not possible
|
300865 |
Axis %1 drive %2 measurement of DC link voltage not possible
|
300875 |
Axis %1 drive %2 fixed link voltage of axes differ
|
300888 |
Axis %1 drive %2 parameterization error in current control adaption
|
300900 |
Axis %1 drive %2 stop A triggered
|
300901 |
Axis %1 drive %2 stop B triggered
|
300906 |
Axis %1 drive %2 safe braking ramp exceeded
|
300907 |
Axis %1 drive %2 tolerance for safe operational stop exceeded
|
300908 |
Axis %1 drive %2 stop C triggered
|
300909 |
Axis %1 drive %2 stop D triggered
|
300910 |
Axis %1 drive %2 stop E triggered
|
300911 |
Axis %1 drive %2 error in one monitoring channel
|
300914 |
Axis %1 drive %2 safe velocity exceeded
|
300915 |
Axis %1 drive %2 safe end positions exceeded
|
300950 |
Axis %1 drive %2 is not safely referenced
|
300951 |
Axis %1 drive %2 test stop is running
|
300952 |
Axis %1 drive %2 acceptance test mode is active
|
301701 |
Axis %1 drive %2 limit value for safe velocity too large
|
301702 |
Axis %1 drive %2 track inversion incorrect
|
301703 |
Axis %1 drive %2 encoder/motor type are not compatible
|
301704 |
Axis %1 drive %2 pole pair width/division of linear scale (internal) out of range
|
301705 |
Axis %1 drive %2 distance-coded scale incorrectly parameterized
|
301706 |
Axis %1 drive %2 parameterization of cam position invalid
|
301707 |
Axis %1 drive %2 parameterization of modulo value for safe cam (SN) invalid
|
301708 |
Axis %1 drive %2 actual value synchronization not allowed
|
301709 |
Axis %1 drive %2 submodule with integrated linearization invalid
|
301710 |
Axis %1 drive %2 resolution SSI motor measuring system invalid
|
301711 |
Axis %1 drive %2 transmission length SSI motor measuring system invalid
|
301712 |
Axis %1 drive %2 multiturn SSI motor measuring system invalid
|
301713 |
Axis %1 drive %2 resolution SSI direct measuring system invalid
|
301714 |
Axis %1 drive %2 transmission length SSI direct measuring system invalid
|
301715 |
Axis %1 drive %2 multiturn SSI direct measuring system invalid
|
301716 |
Axis %1 drive %2 SSI direct measuring system without incremental signals not possible
|
301717 |
Axis %1 drive %2 SSI transmission timeout
|
301718 |
Axis %1 drive %2 combination of motor/power section invalid
|
301719 |
Axis %1 drive %2 power section data incomplete
|
310505 |
Axis %1 drive %2 measuring circuit error of absolute track, code %3
|
310606 |
Axis %1 drive %2 external valve voltage supply failed
|
310607 |
Axis %1 drive %2 valve not responding
|
310608 |
Axis %1 drive %2 speed controller at limit
|
310609 |
Axis %1 drive %2 encoder cut-off frequency exceeded
|
310610 |
Axis %1 drive %2 wrong piston position
|
310611 |
Axis %1 drive %2 pressure sensor failed
|
310612 |
Axis %1 drive %2 force limitation off
|
310701 |
Axis %1 drive %2 speed controller cycle time invalid
|
310702 |
Axis %1 drive %2 position controller cycle time invalid
|
310703 |
Axis %1 drive %2 monitoring cycle time invalid
|
310704 |
Axis %1 drive %2 speed controller cycle times of axes differ
|
310705 |
Axis %1 drive %2 monitoring cycle times of axes differ
|
310706 |
Axis %1 drive %2 maximum working speed invalid
|
310707 |
Axis %1 drive %2 STS configuration of axes differ
|
310708 |
Axis %1 drive %2 number of encoder marks of measuring system invalid
|
310709 |
Axis %1 drive %2 error in piston diameter or piston rod diameter
|
310710 |
Axis %1 drive %2 distance-coded scale incorrectly parameterized
|
310750 |
Axis %1 drive %2 feedforward gain too high
|
310751 |
Axis %1 drive %2 proportional gain for speed controller too high
|
310752 |
Axis %1 drive %2 integral gain for speed controller invalid
|
310753 |
Axis %1 drive %2 D component for speed controller invalid
|
310754 |
Axis %1 drive %2 friction compensation gradient too high
|
310755 |
Axis %1 drive %2 area factor too high
|
310756 |
Axis %1 drive %2 controlled system gain is less than or equal to zero
|
310757 |
Axis %1 drive %2 blocking frequency > Shannon frequency
|
310758 |
Axis %1 drive %2 natural frequency > Shannon frequency
|
310759 |
Axis %1 drive %2 bandwidth numerator larger than double blocking frequency
|
310760 |
Axis %1 drive %2 bandwidth denominator greater than double natural frequency
|
310761 |
Axis %1 drive %2 proportional gain of force controller too high
|
310762 |
Axis %1 drive %2 integral gain for force controller invalid
|
310763 |
Axis %1 drive %2 D component of force controller invalid
|
310764 |
Axis %1 drive %2 controlled system gain for force controller is less than or equal to zero
|
310771 |
Axis %1 drive %2 gain in fine area of valve characteristic is less than or equal to zero
|
310772 |
Axis %1 drive %2 gain in rough area of valve characteristic is less than or equal to zero
|
310773 |
Axis %1 drive %2 gain at end of saturation area of valve characteristic is less than or equal to zero
|
310774 |
Axis %1 drive %2 zero area and knee area of valve characteristic overlap
|
310775 |
Axis %1 drive %2 knee area and saturation area of valve characteristic overlap
|
311710 |
Axis %1 drive %2 resolution SSI motor measuring system invalid
|
311711 |
Axis %1 drive %2 transmission length SSI motor measuring system invalid
|
311712 |
Axis %1 drive %2 multiturn SSI motor measuring system invalid
|
311716 |
Axis %1 drive %2 SSI measuring system without incremental signals not possible
|
311717 |
Axis %1 drive %2 SSI transmission timeout
|
380001 |
Profibus-DP: startup error, reason %1 parameter %2 %3 %4.
|
380003 |
Profibus-DP: operating error, reason %1,parameter %2 %3 %4.
|
380005 |
Profibus-DP: bus access conflict, type %1, counter %2
|
380020 |
Profibus-DP: SDB1000 error %1 for SDB source %2
|
380021 |
Profibus-DP: default SDB1000 was loaded
|
380022 |
Profibus-DP: configuration of DP master has been changed
|
380040 |
Profibus-DP: configuration error %1, parameter %2
|
380050 |
Profibus-DP: multiple assignment of inputs on address %1
|
380051 |
Profibus-DP: multiple assignment of outputs on address %1
|
380060 |
Profibus-DP: alarm %1 on logical address %2 from unassigned station
|
380070 |
Profibus DP: no input slot available for base address %1 (length %2)
|
380071 |
Profibus DP: no output slot available for base address %1 (size %2)
|
380072 |
Profibus DP: output slot for base address %1 (size %2) not allowed
|
380075 |
Profibus DP: DP I/O failure slave %1
|
380500 |
Profibus-DP: fault on drive %1, code %2, value %3, time %4
|
400102 |
Delete DB 2 in the PLC and restart
|
400103 |
Delete DB 3 in the PLC and restart
|
400106 |
Delete DB 3 in the PLC and restart
|
400109 |
Delete DB 9 in the PLC and restart
|
400171 |
Delete DB 71 in the PLC and restart
|
400172 |
Delete DB 72 in the PLC and restart
|
400173 |
Delete DB 73 in the PLC and restart
|
400174 |
Delete DB 74 in the PLC and restart
|
400250 |
NCK sign-of-life monitoring
|
400251 |
NCK has not started up
|
400252 |
Sign-of-life monitoring
|
400260 |
Failure of machine control panel 1
|
400261 |
Failure of machine control panel 2
|
400262 |
Failure of manual operating device
|
400604 |
Set change with M06 in the machine data
|
400902 |
Impermissible channel no. parameter in FC 9
|
401502 |
Impermissible axis no. parameter in FC 15
|
401602 |
Impermissible axis no. parameter in FC 16
|
401702 |
Impermissible spindle IF no. parameter in FC 17
|
401805 |
Impermissible axis no. parameter in FC 18
|
401901 |
Impermissible BAG no. parameter in FC 19
|
401902 |
Impermissible channel no. parameter in FC 19
|
402501 |
Impermissible BAG no. parameter in FC 25
|
402502 |
Impermissible channel no. parameter in FC 25
|
410150 |
Area in M group decoder list is too large
|
810001 |
Error OB_event
|
810002 |
Synchronous error
|
810003 |
Asychronous error
|
810004 |
Stop/Interrupt event
|
810005 |
Order form execution event
|
810006 |
Error communication event
|
810007 |
Error H/F system event
|
810008 |
Error diagnostics data from modules
|
810009 |
User-diagnostics event |